Anyone Handled the Mossberg Shockwave?

[Conax]

My brother was a Remington 870 guy while I always shot a Winchester 1300.
They're all pretty good but we do have our personal favorites. That 1300 was stone reliable, fed everything and had a slick action. I gave a Mossberg to my kid for his birthday, I like them just fine. The Mossbergs have really caught on in modern times, lots of accessories available and they're good guns at good prices.

[BrokenolMarine]

I ordered a sling swivel for my Shockwave and it came in this evening. Installation would have taken about three minutes, but I took the time to take pictures, so I could share it with ya'll. This is the GG&G Quick Release single point side sling mount. Just what I was looking for.


To get started, I first insured the firearm was unloaded, the chamber was clear, and I had the tools I needed on hand. Proper sized punch, blue loc-tite, and the parts kit which included the allen wrench, plastic pads, the receiver for the quick release sling swivel and the screw that will replace the trigger retaining pin.

01 ready to start.jpg

Here is a close up peek at the kit.

02 the swivel kit.jpg

The first step was to knock out the trigger retaining pin. I used a proper sized punch, and a light tap with a nylon hammer. No problem at all.

03 remove trigger pin.jpg

Since my memory is VERY short I forgot to take a picture of the next step, but the whole process is easy as pie. Without pulling on the trigger assembly, I put the smaller of the two plastic guards on the screw and inserted it from the right side, since I am right handed and wanted the sling swivel on the left. Another light tap with the nylon mallet seated the screw.

I put the larger of the plastic guards over the screw on the left side, readying the screw to receive the swivel base. I put a couple drops of Loc-tight in the threads of the base and lightly screwed it in place until it contacted the plastic guard. For aesthetics, I turned the logo UP. I then used the allen key to turn the screw from the right side a 1/2 turn to draw the assembly tight, but not TOO tight. I worked the action to insure the bolt functioned smoothly.

04 installed the base.jpg

If the base assembly is too tight it will flex the aluminum receiver and bind the bolt. If this happens, loosen the screw 1/4 turn and try again. Do this BEFORE the loc-tight sets.

Now test the quick release swivel.

05 removable swivel.jpg

I always mark and save any parts removed...

06 save the pin.jpg

I plan to use a single point sling, and it worked out perfectly.
Fits well and detaches with a pop of the button.

07 Single point sling.jpg

08 pops right off.jpg

No permanent changes to the firearm and swapping back to the original setup would take about two minutes. If I remember where I stored the dang pin when the time comes. (That's why I have a large tupperware storage bin with all the gun parts stored in there. It's a matter of digging thru and finding that small bag among all the parts.)

[Joezilla]

Nice job!

Joe

[Joe.45]

I haven’t shot the Shockwave but in my local Florida Gun forums many people are re-selling them and I have seen them for as low as $275/$300.
My choice for HD is a Remington 870 Marine Magnum with a 18 inch barrel.

[JEBar]

thanks for taking the time and effort to record and post the pictures along with your comments ....

[Redthies]

Great write up BoM. I agree with the reasons you chose the Mossberg. Two reasons I like Mossberg shotguns are the safety location and slide release, although the slide release won’t come in to play on my new semi auto. The safety is in the most natural spot.

[Mgderf]

Great write up BoM. I agree with the reasons you chose the Mossberg. Two reasons I like Mossberg shotguns are the safety location and slide release, although the slide release won’t come in to play on my new semi auto. The safety is in the most natural spot.

Same for me.
I grew up with a Mossberg 500 12ga and I just can't get used to any safety that's not on the tang.
Seems like the most natural placement, but I'm sure that's just what I'm used to.

For those reasons, and just because I'm a Mossy fan, I bought the Shockwave.
I purchased the .410bore model, but plan on adding all three flavors to the herd.
I bought the .410 first because I found it on sale for a decent price, and because I thought it would be the harder of the three to locate.

I'll buy the 12ga and 20ga as the come available, and as funds allow.
I already have the model 500 in 12ga, 20ga, and .410bore so the Shockwaves are just adding to the collection.

[Redthies]

I think the .410 version would sell the least, but would make an awesome “hey there’s dinner” gun for in the pickup. We have grouse everywhere here and that would slay them nicely!

[Redthies]

Oh, and @BrokenolMarine: I have the exact same hammer on my workbench. It’s been going strong for close to 20 years!

[dave77]

New addition to my Shockwave, nice 6 shot shell holder with a Picatinny rail. I have the model with the laser so had to get some longer mounting screws. Had already added the light, just need a sling and holder like BrokenolMarine put on his and I'll be done.

Darn, just realized I need to get something to put on the new Picatinny rail.

[fortyshooter]

I have the 20 ga. and added my Streamlight for a nice bedside defense gun.

[Mgderf]

I ended up being gifted the 12ga model Shockwave as payment for services rendered. To make it even better, these were "services" that I rendered with ZERO expectation for remunerations.
I had no clue it was headed my way, which made the gift even more special.
So, I now have the 12ga and the .410bore. The 20ga will follow shortly I'm sure.

As a side note, I made a discovery purely by accident, but one that others may find handy as well.
The .410bore version of the Shockwave has a smaller profile handguard than the 12ga.
The .410 versions handguard fits perfectly, and is held in place nicely, by an old, no longer used, Mag-Lite wall clip.
My .410 Shockwave now hangs at the ready, just inside a strategic doorway in my house.
A quick grab and it's ready for action.

[dave77]

Finally shot my 12 gauge Shockwave. 5 rounds of 00 buckshot and I was very impressed. Recoil was not as bad as I was expecting but I have the laser equipped model and the laser housing has a slightly raised section that is right at the base of my thumb, not sharp but still hurts when I fire it. Will find some kind of sturdy, smooth tape to wrap around it.

[Ernie]

Bought the 20 gauge shockwave today. I have been considering it for 4 weeks and waiting for someone else to snap it up. Stopped in today and it was still there. They knocked a few bucks off so I brought it home. 12 gauge is rough for me to handle with a pistol grip and I have not seen 410 shells in ages so the 20 gauge seemed like a good choice. Now I want to find a light and mount. I may shoot it tomorrow and I will let you know how it works for me.

[fortyshooter]

Congrats Ernie on the 20 ga. ! I think that size is right handy and still packs a good punch.

[BrokenolMarine]

I had forgotten about this old thread, and when I updated my shockwave a few months ago with a light and red dot, started a new thread. Check it here.

http://henryrifleforums.com/viewtopic.php?f=18&t=12711