Big Boy Steel rail?

Post by **olywa** » Mon May 15, 2017 9:10 am

I currently have a Skinner peep on my 357 and it works well for shorter ranges and snap shots. I wanted to put a low power scope on this rifle but the only mount I know of is the one that Henry makes. Unfortunately this places the scope much higher above the bore than I prefer. Is anyone one aware of a Weaver rail that will fit this receiver using the existing mount holes?

I'm not worried about the rear sight clearance since I've already removed it and placed a blank in the dovetail. Though I prefer irons on a lever gun, my old eyes would appreciate a compact scope or red dot. Anything larger, like a 3-9X40, just sits too high above the bore. This ruins a good cheek weld and hampers the natural pointability of this slick little rifle.

Post by **CT_Shooter** » Mon May 15, 2017 9:16 am

Welcome to the forum from CT, olywa. Several forum members have scoped their Big Boys and will happy to help you out.

Post by **clovishound** » Mon May 15, 2017 9:47 am

I got a Weaver rail at my LGS. It fits two of the drilled/tapped holes on my Big Boy steel perfectly. The third required a little work with a small round file. I went with this rail because it was cheap and readily available. I wanted to try out a small red dot scope on the Henry. I was planning on replacing it with the Henry rail, if I decided to keep the scope on the Henry. That was almost 2 years ago, and the Weaver is still on it.

Post by **JEBar** » Mon May 15, 2017 9:49 am

welcome indeed .... hope you will read and post often .... we have the Henry rails on all three of our Henry rifles so I can't help with your question, there is on doubt that some of our folks will be able to do so .... please consider taking a look at our How Many ? thread (link below) and add your Henry to our community total

http://henryrifleforums.com/viewtopic.p ... 710#p39710

Post by **clovishound** » Mon May 15, 2017 8:11 pm

I forgot to mention that the Weaver rail on my BB is definitely lower profile than the Henry rail. I believe the Weaver ran a little under $10. It's aluminum, so the modification to it was pretty easy. Just don't take too much off at one time. I thought about using a counter sink bit in the drill press, but decided set up time would be too time consuming, so I free handed it with a small file. Didn't take long.

Rugerfanboy · Post by **Rugerfanboy** » Tue May 16, 2017 12:24 am

olywa wrote:I currently have a Skinner peep on my 357 and it works well for shorter ranges and snap shots. I wanted to put a low power scope on this rifle but the only mount I know of is the one that Henry makes. Unfortunately this places the scope much higher above the bore than I prefer. Is anyone one aware of a Weaver rail that will fit this receiver using the existing mount holes?

I'm not worried about the rear sight clearance since I've already removed it and placed a blank in the dovetail. Though I prefer irons on a lever gun, my old eyes would appreciate a compact scope or red dot. Anything larger, like a 3-9X40, just sits too high above the bore. This ruins a good cheek weld and hampers the natural pointability of this slick little rifle.

http://rangerpointstore.com/shop-all/ma ... unt-rails/

Edit: Resized Picture.

Rugerfanboy · Post by **Rugerfanboy** » Tue May 16, 2017 12:45 am

The one for the Henry Big Boy Steel will be black and is money well spent in my opinion. It's a better quality rail than the Henry rail cause once screwed down...it's not coming loose unlike the Henry rail...which will come loose over time with magnum ammo. Been there and done that and I won't go back. I have two of these rails mounted on a Henry Big Boy Steel chambered in 357 Magnum and another one chambered in 44 Magnum.

Post by **clovishound** » Tue May 16, 2017 11:51 am

That is a different rail than the one I used.

Post by **Cofisher** » Tue May 16, 2017 12:10 pm

RFB, who makes that rail?

Rugerfanboy · Post by **Rugerfanboy** » Tue May 16, 2017 4:51 pm

Cofisher wrote:RFB, who makes that rail?

Ranger Point Precision...there based out of Cypress, Texas. I'll post a link to there website below. The rail for the Henry Big Boy Steel is a precision rail. It and my new scope setup has moved my groups under a inch @ 100 yards. What I know now of this rail...I'd gladly pay $50 bucks with a big smile on my face.
http://rangerpointstore.com/shop-all/ma ... unt-rails/

Post by **Cofisher** » Tue May 16, 2017 7:43 pm

Thanks

Post by **olywa** » Wed May 17, 2017 12:34 am

Rugerfanboy - thanks for the link! I have one ordered.

Rugerfanboy · Post by **Rugerfanboy** » Sat May 20, 2017 3:51 pm

Cofisher wrote:Thanks

Your welcome...!!!

Rugerfanboy · Post by **Rugerfanboy** » Sat May 20, 2017 4:06 pm

olywa wrote:Rugerfanboy - thanks for the link! I have one ordered.

Your welcome...!!!

Just remember to use some blue loctite on the screws after you clean the oil out of the holes on top of the receiver. Also, the rail will have some oil on it and will need to be degreased as well.

rwortman · Post by **rwortman** » Sun May 28, 2017 2:45 pm

I have a Ranger Point rail on mine too. For the reason the original poster stated, to lower the scope. I bought a Weaver rail for a Marlin and thought about modifying it. I figured it would not be as strong with an elongated hole so I bought the Ranger Point one. I also replaced the rear sight with a folding leaf in case I was out and about and had a scope problem. I never liked that spring loaded ramp thingie.

Henry Rifle Forums

Big Boy Steel rail?

Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?

Re: Big Boy Steel rail?