What did you do at your reloading bench today?

[Travlin]

I am surprised that you don't cast your own bullets. Starting in 1969 , when i bought a gun I bought a mould and sizing die for the Lyman bullet sizer. That way I knew that I would always have bullets for all the calibers that I shot.

[Travlin]

As an aside the "mould" is the way it is spelled in the Lyman Cast Bullet Handbook. "Mold" is something smelly and black and very bad for your health.

[Hatchdog]

Yesterday I decapped and polished 118 32 H&R mag cases. Next up is to add some powder, primer and bullet and magically turn them into cartridges. I’m using the Hornady 85 gr XTP over 5.3 of Bluedot and a standard CCI primer. Makes for a nice soft shooting load for my SP101. Watch out bowling ping, I’m gunning for you.

IMG_5778.jpeg (2.66 MiB) Viewed 1178 times

[Hatchdog]

Yesterday I added primer, powder and bullets to the brass seen above and now I have an additional 116 32 H&R’s to shoot up this spring. Plus the 11 left overs from the last loading session for this caliber. Found two split cases which makes several from this lot of brass. I bought it used from a guy with a set of dies so I don’t know how many times it’s been loaded. It gets a very close inspection due to the number of split cases I have found.

Hornady 85 grain XTP over 5.3 of Bluedot and CCI standard sm pistol primer.

IMG_5793.jpeg (2.43 MiB) Viewed 1513 times

IMG_5794.jpeg (2.08 MiB) Viewed 1513 times

IMG_5792.jpeg (1.73 MiB) Viewed 1513 times

[Vaquero]

Well, yesterday morning I loaded some 44 and 444s for some off the deck plinking,
Then after the plinking was over I decapped all that brass plus the 45 Colt stuff that I shot last weekend.
Two separate loads through the tumbler and it's all shiny and ready to start all over.

RP

[Hatchdog]

Well, yesterday morning I loaded some 44 and 444s for some off the deck plinking,
Then after the plinking was over I decapped all that brass plus the 45 Colt stuff that I shot last weekend.
Two separate loads through the tumbler and it's all shiny and ready to start all over.

RP

It’s a vicious circle isn’t it?

[Vaquero]

Well, yesterday morning I loaded some 44 and 444s for some off the deck plinking,
Then after the plinking was over I decapped all that brass plus the 45 Colt stuff that I shot last weekend.
Two separate loads through the tumbler and it's all shiny and ready to start all over.

RP

It’s a vicious circle isn’t it?

Yep.
Not sure if I shoot to load, or load to shoot??
I do enjoy both...

RP

[JVogler]

Deprimed and flared about 30 357magnum shells to make up a box of 50 once fired shells. Have about 500 shells of 38special/357magnum tumbled and ready to be deprimed and separated into once fired or multi fired. I separate shells according to headstamp also.

[JVogler]

It's Thursday night and I'm still working on last weeks shell acquisition. Deprimed and flared 100 38special and 100 3577magnum more shells today. At least I'm well set with brass for all the calibers I load for . I load 3 calibers to shoot in my brothers weapons.

[JVogler]

It's Thursday night and I'm still working on last weeks shell acquisition. Deprimed and flared 100 38special and 100 3577magnum more shells today. At least I'm well set with brass for all the calibers I load for . I load 3 calibers to shoot in my brothers weapons.