What did you do at your reloading bench today?

[Grunt67]

Started trimming 45/70 brass. Some needed trimming, all need chamfered, deburred. Starline new brass.

[brettitt41]

Started trimming 45/70 brass. Some needed trimming, all need chamfered, deburred. Starline new brass.

What do you use to trim your 45-70 brass? I have a Worlds Perfect Trimmer for all my bottleneck cartridges but nothing for my straight wall 45-70.

[runnin n gunnin]

For 45-70 I use an LE Wilson case trimmer. Extremely hearty and well made.

.jpg (42.1 KiB) Viewed 3450 times

You will also need a rifle trimmer case holder

external-content.duckduckgo.com.jpg (47.64 KiB) Viewed 3450 times

Here are links to Midway USA to look at the product.

https://www.midwayusa.com/product/1012820942
https://www.midwayusa.com/product/1012782275?pid=214923

LE Wilson is heavy duty and easy to use. I got the attachment to use an electriv drill as opposed to the crank. I sued it for all of my brass, all calibers until I bought the Lyman Brass Smith for my shoulder brass. (45-70 will not work in the Lyman)

The Wilson is well worth the money in my humble opinion.

[BigAl52]

I use a Forester. They work well also.

[Grunt67]

Started trimming 45/70 brass. Some needed trimming, all need chamfered, deburred. Starline new brass.

What do you use to trim your 45-70 brass? I have a Worlds Perfect Trimmer for all my bottleneck cartridges but nothing for my straight wall 45-70.

I use a Forster Cam-Lok trimmer. Best I've used . Easy to set up, uses Hornady shell holders. Check it out, I think you'll see what I
mean. I had ( well, still have ), a Wilson trimmer, but like the Hornady much better, works better. Also, whatever trimmer you get, you're going to need to get the RCBS "Large" chamfer/deburr tool. Standard size won't work.
Have fun, hope this helps.

[BigAl52]

UPS just dropped off 6 boxes of Nosler 41 mag bullets. Im set for a while. Maybe

[JEBar]

good buy on those 41's .... looking forward to your range reports after you get some loaded

[RanchRoper]

100 rounds of 200 gr 7.0 Universal are on the schedule for today.

[JEBar]

this morning I decided to load 100 full power 44 Mags for use in our Henry .... when I went out to setup our portable reloading station it turned out to be way too hot, too humid and too windy .... as an alternative, I decided to stay inside and use our Lee hand press .... that is something I haven't done since the late 60's .. .. doing so quickly reminded me of why I bought a RCBS Rock Cruncher .... it took a while but I completed loading 100 rounds using CCI Large Pistol Magnum Primers, 23.8 g of W296, and 240 gr Nosler JSP bullets .... well before I finished using a Lee crimping die as the last step on the final round, I'd made up my mind to wait out the weather the next time I decide to make some bullets ..

[Rifletom]

Dang! Now that's commitment. Good job Jim. How are those handhelds to use?

[runnin n gunnin]

Well, weather was cool today, 95 12% humidity, so I set up a 270 range and worked the black guns.

20200629_090735.jpg (303 KiB) Viewed 3507 times

I have about 1,000 pieces of brass to clean and prep now, will start tomorrow.

Oh yeah, I had to share the range today with a friend

20200629_094530.jpg (223.51 KiB) Viewed 3507 times

[Rifletom]

r-n-g, sure like the range, but, I do NOT like those rattlers. Yikes!

[runnin n gunnin]

Yeah, he was a big 3 footer with 12 rattles, been around for a while.

[BigAl52]

He would have been a dead one if I would of seen him

[BigAl52]

this morning I decided to load 100 full power 44 Mags for use in our Henry .... when I went out to setup our portable reloading station it turned out to be way too hot, too humid and too windy .... as an alternative, I decided to stay inside and use our Lee hand press .... that is something I haven't done since the late 60's .. .. doing so quickly reminded me of why I bought a RCBS Rock Cruncher .... it took a while but I completed loading 100 rounds using CCI Large Pistol Magnum Primers, 23.8 g of W296, and 240 gr Nosler JSP bullets .... well before I finished using a Lee crimping die as the last step on the final round, I'd made up my mind to wait out the weather the next time I decide to make some bullets ..

Tell Maureen your mounting one to the kitchen table next time Jim

[JEBar]

Tell Maureen your mounting one to the kitchen table next time Jim

.... she has way tooooo many loads on hand for her Smith & Wesson for me to even consider that

[runnin n gunnin]

Trust me, I am no snake wrangler, he is definitely dead thanks to CCI .45 Colt snake shot !

[JEBar]

Trust me, I am no snake wrangler, he is definitely dead thanks to CCI .45 Colt snake shot !

action I can identify with and fully support ..

[JEBar]

Dang! Now that's commitment. Good job Jim. How are those handhelds to use?

my first reloading system was a Lee Loader that was purchased back in the mid 60's https://leeprecision.com/lee-loader-357-mag.html .... it worked but the occasional detonation using a hammer to insert a primer motivated me to look for a replacement system .... the Lee Hand Press proved to be a system I could afford .... it most certainly can produce high quality ammo but using it for mass production can be tedious .... from my experience, it excels serving as a highly portable press used to produce a few rounds at a time .... example : when developing a new load at a range .... take empty brass that is ready to add powder and seat a bullet .... have that die in the Lee Hand Press load a few test rounds .... its simple to adjust powder charges and even bullets as you test various combinations .... as noted above, it can be used to produce a large number of bullets but it is far from the best choice to do so

[Rifletom]

I too had(still have, actually) a Lee Loader for my 30-30. Using that hammer thingy for primers got me thinking of a press mighty fast. Bought a RCBS Rock Chukar in '77-78.