Project Rifle Rest

Mistered · Post by **Mistered** » Sun Sep 01, 2019 9:32 pm

'Bench testing' a contraption I threw together today. A small car scissor jack, a hard rubber 'V' block for a boat trailer and all mounted to a board which I can clamp to the table and I have a 'prototype' adjustable rifle rest! It actually works quite well - at least just testing it for sighting and positioning anyway.
I cut a piece of thick leather and glued it in the 'V' block and slathered it with neatsfoot oil to soften it to protect stocks.

: IMG_1616.JPG (403.95 KiB) Viewed 2364 times

Post by **RanchRoper** » Sun Sep 01, 2019 11:17 pm

Looks pretty solid.

Mistered · Post by **Mistered** » Mon Sep 02, 2019 12:15 am

Yea the hardest part was figuring out how to secure the V block to the jack.
Well since it has a 1/2" hole for a bolt I cut a short section of 1/2" aluminum round stock the width of the block, drilled a 1/4" hole through the center of it and pressed it into the hole.
I then cut a hole in the block at the bottom of 'V' and pressed a 1/4" bolt through it and the hole in the rod.
With a flat washer on the underside and a nut on the bolt I tightened it and the aluminum rod was pulled down and secured the block.
The bolt head was pulled down below the V groove and out of sight so no interference!

Post by **Mags** » Mon Sep 02, 2019 2:09 am

.
Now that is clever!

Mistered wrote: ↑
Sun Sep 01, 2019 9:32 pm
'Bench testing' a contraption I threw together today. A small car scissor jack, a hard rubber 'V' block for a boat trailer and all mounted to a board which I can clamp to the table and I have a 'prototype' adjustable rifle rest! It actually works quite well - at least just testing it for sighting and positioning anyway.
I cut a piece of thick leather and glued it in the 'V' block and slathered it with neatsfoot oil to cushion and protect stocks.

IMG_1616.JPG

Post by **markiver54** » Mon Sep 02, 2019 9:23 am

Good idea Ed! Matter of fact, I think I have one of those old jacks out in my shop. Might be a copycat.

Post by **JEBar** » Mon Sep 02, 2019 9:55 am

nice use of a stabilizer .... well designed and built .... I can't see the other end of the adjustment screw but as I'm sure you know, depending on its design, a small variable speed drill with a 3/4" socket or heavy Allen wrench could provide you with quick height adjustment

Mistered · Post by **Mistered** » Mon Sep 02, 2019 11:05 am

I can't see the other end of the adjustment screw

Its a large tab actually with a hole in it for the original crank handle.
Easy to spin up or down by hand but if this all works and I continue to use it I may bend a piece if 1/4' round stock into a small crank handle and weld it on.

I might replace the rubber V block with a shaped hardwood block - again that is if this works out which I should know today!

Post by **JEBar** » Mon Sep 02, 2019 12:13 pm

10-4 on the "hole in it for the original crank handle" .... I've found that an Allen wrench (about a 1/4") with the long end inserted in a drill chuck works well .... having something like that could sure collapse jack when packing it for travl

Post by **Rifletom** » Mon Sep 02, 2019 12:57 pm

markiver54 wrote: ↑
Mon Sep 02, 2019 9:23 am
Good idea Ed! Matter of fact, I think I have one of those old jacks out in my shop. Might be a copycat.

I was thinking the very same thing Mark. 'ol Mistered came up with a very novel idea. I like it! Search is on!

Post by **Shakey Jake** » Mon Sep 02, 2019 1:04 pm

I'm kinda interested in what's in that jar! Hmmm....

Ojaileveraction · Post by **Ojaileveraction** » Mon Sep 02, 2019 2:40 pm

I bet neatsfoot oil.

Shakey Jake wrote: ↑
Mon Sep 02, 2019 1:04 pm
I'm kinda interested in what's in that jar! Hmmm....

Post by **Rifletom** » Mon Sep 02, 2019 3:05 pm

Ha! I think Shakey Jake is on to something.

Mistered · Post by **Mistered** » Mon Sep 02, 2019 3:33 pm

I'm kinda interested in what's in that jar! Hmmm....

Nothing special - just Miller beer!

However I'll have to call my rest a success!

I was testing some new 30-30 loads out as well so it was a two-fer.
This is five shots of some mixed 170 grain bullets I found while re-arranging my bench so I loaded them up - not a great group and I didn't expect much. They were just some loose bullets to get rid of.

: 170.JPG (64.07 KiB) Viewed 1110 times

Now this is much different. This is a six shot group with 150 grain Spire Point bullets. I previously mentioned how SP bullets can make a tackdriver out of a 30-30 and this is proof. Not bad for a 53 year old rifle!

: IMG_1621.JPG (63.69 KiB) Viewed 1110 times

I had to do a sight swap around on my Henry and shot a few just to make sure to make sure it was what I needed. I'll give it touch up later.

: IMG_1623.JPG (68.11 KiB) Viewed 1110 times

Bottom line is my rest works well and I don't think I am going to change anything right now. It supported my rifles very well and I attribute tighter groups to it. I do need to find a seat with the proper height that works for this. I have a heavy duty plastic grocery store packing crate that worked very well just a bit too tall so I I'll address this later.

: IMG_1620.JPG (139.88 KiB) Viewed 1110 times

Post by **Mags** » Mon Sep 02, 2019 6:59 pm

.
I'll grant you success credit too. Well done. Now about that Miller beer ... is that factory or home brew?

Mistered wrote: ↑
Mon Sep 02, 2019 3:33 pm

I'm kinda interested in what's in that jar! Hmmm....

Nothing special - just Miller beer!

However I'll have to call my rest a success!
...

Mistered · Post by **Mistered** » Mon Sep 02, 2019 7:05 pm

is that factory or home brew?

Unfortunately factory - but I use to make my own beer many years ago - got into it as a hobby but man it takes a lot of time!

Henry Rifle Forums

Project Rifle Rest

Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest

Re: Project Rifle Rest