Potato and Onion Bin

[PT7]

Always a good thing when the bin is a win: "...the boss is pleased."

Looking forward to the final photo shoot.
Congrats on finishing, Marine.

[BrokenolMarine]

.
Very nicely done! I have a question, what keeps the spuds and onions from falling off the back of the individual bin and into the lower bin when there is a lot in them in there and you open a bin?

The bins have about fourteen and a half inches width, and about nine inches depth, nearly ten inches height of usable interior space. The rear of the bin has a four inch wire back. The contents will roll forward when the bins are tilted open, and a whole five pound bag of taters easily fits with room to spare. Watch for the pics.

[BrokenolMarine]

THE PICS

Went out in the shop after dinner and got ready to install the pull handles and hinges. First step? Gather all the tools I would need.

80 gather up tools.jpg (203.18 KiB) Viewed 5413 times

The first thing I did was to place each bin in the bench vise with the top edge facing me, which placed it upside down. No matter, the handles were going to be centered in the 1" wide rail.
Next I covered the rail with blue painters tape, to give me a surface to right freely on without worrying about having to damage the finish.
Next I broke out the centering rule... I love this thing and use it a lot.

81 centering rule.jpg (187.18 KiB) Viewed 5413 times

Place this on something you need to find the center of, and then when the same measurement is indicated on both edges, mark the zero in the center. Done.
I also marked 1-1/2 inches in both directions since the handles screws were 3" on center apart. I then used my pocket square, to mark those locations, then 1/2" up from the edge.
I marked those with the center punch.

82 marked for drilling.jpg (173.77 KiB) Viewed 5413 times

After I rechecked all the measurements... I drilled thru with a 1/16" bit as a pilot hole, then drilled thru with the proper sized bit for the screw for the handles. Perfect alignment on each handle. Slow and steady wins the game. I got all the handles installed and prepared to move to the hinges. Here is the info on the handles as promised.

83 info for handles.jpg (98.57 KiB) Viewed 5413 times

[BrokenolMarine]

Once the handles were done, time to move to the hinges. I placed a hinge on the lower edge of the slot in the cabinet. I folded the hinge to determine which wing I wanted to use, and set a square at 3-1/2 inches to make sure they were consistent in the inset from the edge. I used a center punch to insure the pilot hole for the screws would be properly aligned and drilled carefully, then attached the lower half of the hinge. I shimmed the bins so that they were centered and spaced off the rails, and attached them and moved to the next bin repeating the process.

84 handles and hinges.jpg (225.12 KiB) Viewed 5413 times

If you look closely in this pic ^^^^^ you can see the shims below the bin and along the sides holding the spacing as the hinges are installed. I checked the hinges before placement on each bin to insure the "short" wing (The one without the barrel) was installed down... for consistency.

Slow and steady again, and eventually all the hinges were installed. While drilling one screw hole, the bit slipped and the hole was way out of center. The trick here is to keep toothpicks in the shop. Stick a toothpick into the hole to the bottom, mark the depth with a pencil, then pull it back out. Cut it off just above your mark, dab some glue on the toothpick and then stick it back in the hole. Take a punch and PACK it into the hole flush. Go on to other tasks for about 15 minutes, then come back and remark your center and CAREFULLY drill your new centered hole. The toothpick packed and glued in the old hole prevents the drill from attempting to follow that patch.

The hinges and handles completed, the project is all done and ready to move inside.

85 all done.jpg (128.01 KiB) Viewed 5413 times

[BrokenolMarine]

We moved the bin into the kitchen and installed it in it's slot. It fit perfectly, as I held my breath. There is a central heating and air vent in front of it and my only concern is that it might have been just a tad too wide, but I stayed within my plan and it tweeked right in there. It will live between the antique sideboard Miss Tina found on one of our road trips for a song because the lady wanted "That Monstrosity out of the shop" and the baker's rack we use as a microwave stand.

86 in the kitchen.jpg (192.11 KiB) Viewed 5412 times

87 taters and onions.jpg (177.63 KiB) Viewed 5412 times

Tina filled it with the potatoes and onions last night. The bottom bin will hold either sweet potatoes, or baking potatoes, or a mixture of both, since we don't buy those in bulk.
In answer to the question about the taters/content and opening the bins... again... it's not an issue... here is the tater bin tilted open.

88 open it up.jpg (198.77 KiB) Viewed 5412 times

Tina lined them with paper towels for now, but she expects to line the bottom with clear vinyl in the future, she has it on hand, just has to get a round2it.


So... that's the Potato Bin Project in the can. It was interesting and filled my time. I enjoyed the challenge. I'm not sorry I put in the extra work, and I learned some new techniques and remembered some old ones. I think I'll knock out a knife kit next, or build a box. Something quick. Then find another long project. Oh, wait. Surgery looms... stick with the short stuff for now.

[markiver54]

It fits perfectly and is a true compliment to the kitchen.
Really like the chosen hardware!
Gotta get me one of those centering rules! Gosh, how many times I could have used one.
I have used the toothpick trick before though; works great!
Another fine job Jim!!

[PT7]

Marine, let Tina know she had a good handle on the handles....they look great against the wood color on the bin. Also look very easy to "handle" for opening/closing.

Will look forward to your next "long project." Wood melts in your hands, and ends up beautifully re-fashioned.
Have enjoyed keeping up with your sawdust tales.

Take care, and hope the surgery will go very well with quick recovery.
Bob

[Mags]

.
ah yes! in the latest pictures I can see the wire back. Thanks for pointing that out. Well done! Can't wait to see what comes next

.
Very nicely done! I have a question, what keeps the spuds and onions from falling off the back of the individual bin and into the lower bin when there is a lot in them in there and you open a bin?

The bins have about fourteen and a half inches width, and about nine inches depth, nearly ten inches height of usable interior space. The rear of the bin has a four inch wire back. The contents will roll forward when the bins are tilted open, and a whole five pound bag of taters easily fits with room to spare. Watch for the pics.

[BrokenolMarine]

.
Very nicely done! I have a question, what keeps the spuds and onions from falling off the back of the individual bin and into the lower bin when there is a lot in them in there and you open a bin?

Mags,

If you look.on the previous page, there is an work along pic shot of the installation of the wire backs that shows them clearly. I had intended to have wood backs, but they would have cut the range of travel dramatically.

[BigAl52]

Looks really nice Marine. You are very talented and gifted to be able to create things like that Tina is very lucky. I like that a lot.

[CT_Shooter]

Thanks so much, Marine, for taking us along on another of your fantastic woodworking projects. It's beautiful and functional and skillfully made. There are a few members whose posts I never fail to read. You are among them.

Good luck with the next round of surgery.

So... that's the Potato Bin Project in the can. It was interesting and filled my time. I enjoyed the challenge. I'm not sorry I put in the extra work, and I learned some new techniques and remembered some old ones. I think I'll knock out a knife kit next, or build a box. Something quick. Then find another long project. Oh, wait. Surgery looms... stick with the short stuff for now.

[BrokenolMarine]

It fits perfectly and is a true compliment to the kitchen.
Really like the chosen hardware!
Gotta get me one of those centering rules! Gosh, how many times I could have used one.
I have used the toothpick trick before though; works great!
Another fine job Jim!!

You can also use a tooth pick or break off a piece of a wooden cotton swab handle if you had to remove a door hinge to plane an edge, and found a screw is loose. In this case just mark the height, drop it in the hole, and screw your hardware back in place. It should provide enough additional bite that your hinge remains tight. This keeps you from having to oversize the hole, plug it with a dowel, then redrill.

[Mags]

.
ah yes! in the latest pictures I can see the wire back. Thanks for pointing that out. Well done! Can't wait to see what comes next

.
Very nicely done! I have a question, what keeps the spuds and onions from falling off the back of the individual bin and into the lower bin when there is a lot in them in there and you open a bin?

Mags,

If you look.on the previous page, there is an work along pic shot of the installation of the wire backs that shows them clearly. I had intended to have wood backs, but they would have cut the range of travel dramatically.

[Dahliathemeh]

Very nice indeed! A surefire heirloom!