A Special Build

[BrokenolMarine]

The daughter had been looking to find something special for me for Christmas. She settled on knife blanks. She looked for something I wouldn't easily find. At first she thought Fossilized Poo. But, she found a site selling blanks made from reclaimed wood from the restoration of the decking on the U.S.S. Constitution. Cool... They might not make the most highly figured scales, but they would be special.

01.jpg

02.jpg

[BrokenolMarine]

I spent a couple months with the blanks laying in the box with those certificates, trying to decide how I was going to use the scales. Bowie? Nope, the blanks weren't wide enough. Length? I could fake, bone above and below, some stag maybe... but width would be an issue. A dagger? Nope, the shapes would waste a LOT of the wood. I didn't know what the blanks cost, but the wife hinted they were expensive. I played with various ideas and finally fell back on an old favorite. A Damascus Hunter. I drew the layout on the pad and played with the design for a couple weeks. It had to be right before I cut. I had some bone, some turquoise, and the blanks... but once they were cut, you can't take it back.

03.jpg

The turquoise had to be cut on the wet tile saw.

04.jpg

I finally made the cuts on the last BIG piece of flat turquoise I had, and it worked out fine. The bone I had to cut on the bandsaw.

05.jpg

I cut matching pieces, and they would be the guard and the endcap with the scales between them.

06.jpg

To glue them up, I mixed two part epoxy, but to insure the epoxy doesn't detract from the design, I added a powdered tint to the mix, in this case, deep black. If seen, it will accent rather than detract. It will fill any small gaps in the build.

08.jpg

09.jpg

[BrokenolMarine]

Once the turquoise and bone were cut, I glued the individual pieces into pairs, careful to insure the lengths were matched in ways that would allow them to cover the areas and angles that were needed.

10.jpg

In each step of the assembly, one piece would be glued and clamped to a side, and left to cure for several hours, sometimes overnight. This would NOT be a rapid build. I started with the front of the knife and carefully aligned the front bone/turquoise pair with the front edge and glued and clamped. The next day, I glued up the next pairing. Late that afternoon I removed the clamps and shaped the front pair. Beautiful.

11.jpg

12.jpg

Next I cut the blank to match the space I had laid out for the scales, and tested the fit with the endcap pair.

[BrokenolMarine]

When that worked out, I carefully glued up the first scale and clamped 'er in place.

14.jpg

After it dried, I came back out late in the afternoon, and carefully using the holes in the knife blank as a guide, with a wood block backing to prevent tearout, drilled thru the scale glued on the blank.

15.jpg

Now I could carefully align and glue the second scale into place.

16.jpg

17.jpg

[BrokenolMarine]

Once the scales were glued on, I drilled thru the second scale using the existing scales and blade blank as a guide, then placed the knife vertically in the vise and glued the endcap into place. I used a thin carbon fiber spacer on the endcap to insure the fit. (Hair Short)

18.jpg

21.jpg

After curing overnight, I took the knife out of the vise and began sanding and shaping on the various tools in the shop, and by hand. I got to this point, and had to take a break, it was starting to look good, at 400 grit.

22.jpg

I took another session, took her to 800 grit, then applied golden oak to the wood, filled some small gaps in the turquoise with the tinted epoxy, then when it dried, applied a thin coat of spar varnish. Looking good so far.

23.jpg

I'm thinking three to four thin coats of spar varnish, then wax.... I have nickel silver pins for the holes... don't worry. I made them from rod stock.

[BrokenolMarine]

We still have a ways to go......

[Mags]

We still have a ways to go......

Regardless, looking good, very nice.

[BrokenolMarine]

Thanks my friend. I don't think I'll be using this knife. Display only for obvious reasons. Though, the build IS solid, it could be a working knife... It could be used, but would get dinged and scarred like any other. The construction would hold up.

[Sir Henry]

Wow I’m impressed. I could never do anything like that.

[CT_Shooter]

What a great project to honor those who serve(d) on that historic ship. As always, thanks for sharing the process with us. It's beautiful and a "fitting" tribute to Old Ironsides; your knife literally invites all "hands on deck" once again. Glad she wasn't inspired to get you the petrified poo.

[RetiredSeabee]

That is a beauty, and very thoughtful of your daughter. Maybe the petrified poop will show up in a future project.
One question; Is the Bone natural in that black, or was it dyed?

[BrokenolMarine]

I think the bone is naturall a bone color, but Jantz offers it dyed in a rainbow of colors. Very reasonably priced as well. I mostly use it as accent, but have made a couple small knives with rhino and giraffe scales.

[rickhem]

Imagine the sailors way back when having a kind of a flash of vision, that one day a piece of wood from their boat would find it's way to the handle of a custom knife. I'm sure they'd laugh that off. Maybe a few sailors made things themselves from pieces of the ship, like the trench art from WW1.

From a perspective on the part of the USS Constitution though, it would be interesting if they had a picture database showing what the various pieces of wood from the ship eventually were crafted into. It would be interesting to see how creative minds were able to put those pieces of history to use.

And again, fantastic work BOM, your stuff is always amazing!

[BrokenolMarine]

I think I remember seeing possibles boxes and knives made from scrapes of ship boards/beams in a museum, mostly hand carved and hand fitted by the sailors to pass the downtime. They used what little they could find, and when repairs were made they would make all kinds of things from the leftovers.

[BigAl52]

Nice job BOM. Really like the turquoise on the handle

[BrokenolMarine]

I was almost out. Tina ordered more from the Kingman mine in AZ. It's due in next week. The slab scraps are no longer available, she ordered chunks. I'll have to cut slabs off those for accent pieces. It "may" work to an avantage. We'll see.

[BrokenolMarine]

The new Turquoise came in. Five Pounds of rough rock, $295 with shipping. She caught it on sale and saved a bit off that. So we went ahead and got it now.

I'll be cutting it as needed on the wet tile saw. This WAS a very wet job as the saw would soak me from my chest to my knees. I wore a full face welding shield to protect my eyes. I watched a video on YouTube called "Cutting Turquoise With a Tile Saw." I wish I had watched it a long time ago. The guy had turned the saw round and had the blade turning down away from him. Two advantages....

1. The first is the water is thrown AWAY from you, and any small chips and debris are as well. Well duh....

2. He says he has MUCH better control of the turquoise pulling it through the cut than pushing. HE was cutting quarter sized pieces he had taken from necklaces, down the middle where the lacing had gone to polish to make rings. MUCH smaller pieces and thinner than I would be cutting.

I'll certainly try this when I make my cuts. I will first sand a flat on the bottom of the piece for safety to help with control before I start my cuts. The small loss will be worth the risk.

It will be a bit before I need to cut, but the Turquoise is getting harder to find.

[BrokenolMarine]

Well, I finally got some time to get into the shop and work on the knife again. I inserted the pins, worked on the finish, polished the pins and applied several coats of wax. She's done for now. I will work on building the special display case after I finish a major project for the garage, but the knife turned out pretty well. I, of course, see the areas I wish I'd done better in, but Tina loves it, as does my daughter.

24 done.jpg

I will likely add a couple more coats of beeswax and buff, buff, buff.

[CT_Shooter]

...Tina loves it, as does my daughter.

And me. Great job, Marine.

[daytime dave]

That is a very impressive build marine. Your skills are also impressive.