What did you do at your reloading bench today?

[Vaquero]

Is this levergun 38 special ammo or you shooting it outa a 357 handgun

A handgun, Al.
Gonna trying in the King Cobra, and the nephew has a 38 Rossi revolver that will eat most of it.
I don't really care about shooting a lot of 38 through the 357 rifle or KC.

RP

[NHshtr]

Working on prepping brass. Got 40 cases of 7mm-08 Rem., 40 cases of .44 Rem. and halfway to 40 cases of .243 Win. done today. Will finish the .243 cases and begin to fill 'em all up tomorrow during the snowstorm. What better way to pass time during a blizzard? Also, one eye on the forecast for a decent day to go out and empty them all!

[The Happy Kaboomer]

Loaded 20 ga ahotgun shells.

[Hatchdog]

I found a box of the Speer .308 125 TNT-HP that BigAl suggested I try in my 300 Blackout. So yesterday I assembled quite a few using three different powders loading 3-4 loads of each. I’ll be grouping these Speer’s along with some Hornady’s I loaded earlier. Way overkill for what I plan with this rifle but hey, that’s part of the fun!

C70B241C-D4FA-4272-A50A-5D24E457E88C.jpeg (3.58 MiB) Viewed 1680 times

[BigAl52]

Looks good Hatch. I will be anxiously awaiting the results of those TNT bullets. How much 296?

[Hatchdog]

Looks good Hatch. I will be anxiously awaiting the results of those TNT bullets. How much 296?

I started at 14.5 and went as far as 17.0. My Hornady manual shows 17.5 as max so I stayed just under that. Interesting that Sierra shows 19.0 as max and 16.2 as min. Big difference between the two. I’m using CCI 0041 primers which are considered a magnum primer and my COAL is 2.10 which seems to be the sweet spot according to many who have posted online. Plan is to hit the range tomorrow and give all a try.

[BigAl52]

Looks good Hatch. I will be anxiously awaiting the results of those TNT bullets. How much 296?

I started at 14.5 and went as far as 17.0. My Hornady manual shows 17.5 as max so I stayed just under that. Interesting that Sierra shows 19.0 as max and 16.2 as min. Big difference between the two. I’m using CCI 0041 primers which are considered a magnum primer and my COAL is 2.10 which seems to be the sweet spot according to many who have posted online. Plan is to hit the range tomorrow and give all a try.

I found the same info with 296 as it was all over the board. I had better luck with no issues pushing it over the 17gr. I also read on line with several guys doing the same thing that running it over 17 was better accuracy. Im not sure where I was at as I am away as you know.

[Ernie]

Got my Lee factory crimp die in 44 mag and I am loading up some using 6.5gr Unique. with 240 gr XTP.
My LGS has good amount of powder but still no primers. They had 8 lbs Unique for $249 but I have enough.

[The Happy Kaboomer]

Loaded 150 12 ga shells using Remington STS hulls.......Makes factory looking shells

[BigAl52]

Got my Lee factory crimp die in 44 mag and I am loading up some using 6.5gr Unique. with 240 gr XTP.
My LGS has good amount of powder but still no primers. They had 8 lbs Unique for $249 but I have enough.

Man wish I was there Ernie I would snag that right up

[leverjc]

Back ordered 500 cases of 45 colt 3 days ago and they arrived on my porch about an hour ago. I am clearing my bench to load some up using 200grn Beery's made for 45acp with a hollow base. They mike .452 at the olgive and .454 at the base. They shoot well in my 1911's so I think I will give it a try. I am going to start with 6.5grns to 7grns of Unique. looking for a good light load for my 92.

[leverjc]

Hatch I am also looking forward to your range report. I have about a hundred 300blk cases I am going to load up for my son with the same bullet.

[Hatchdog]

Hatch I am also looking forward to your range report. I have about a hundred 300blk cases I am going to load up for my son with the same bullet.

Here’s a link to my report. Let me know if you would like more specific info as my report is pretty general. On my next Speer 125 test I’m going to take the 296 above 17 grains as it’s been reported that accuracy gets better with a faster load.

http://henryrifleforums.com/viewtopic.php?f=42&t=14682

[leverjc]

I have CFEBLK and LilGun but I have a lot of 296. Thanks

[dmanwarren]

Went to a local gun show yesterday and for the first time in almost 2 years I was able to pickup more than 200 at a time! Prices were in the low end of what I would call the new normal. Now I can load up some extra 9mm and 45acp without getting into my reserve stash!

20230318_191853.jpg (2.73 MiB) Viewed 1560 times

[dmanwarren]

Also picked up some 454 casull brass but no 35 Remington to be found loaded or brass.

[Vaquero]

Also picked up some 454 casull brass but no 35 Remington to be found loaded or brass.

Nice score, yep 35 Rem is hard to come by, brass or ammo.
I did see some 200gr. Win. Power points a month ago at one shop.
But, it was $58.99 + tax, glad I started loading for it a good while back.

RP

[dmanwarren]

Vaquero, I bought 3 boxes of factory Hornady just to get started and have something to reload. Those cost me $48 a box. I wish Starline would make 35 Remington then I could at least get on a backorder list.

[Vaquero]

Vaquero, I bought 3 boxes of factory Hornady just to get started and have something to reload. Those cost me $48 a box. I wish Starline would make 35 Remington then I could at least get on a backorder list.

Sadly, that is one caliber that they have never offered that I know of.
Remington and Winchester have offered it in the past. I have a bag of each new 50 pcs. They've been sitting in the cabinet for a while now.
Good luck on the search.

RP

[Vaquero]

Vaquero, I bought 3 boxes of factory Hornady just to get started and have something to reload. Those cost me $48 a box. I wish Starline would make 35 Remington then I could at least get on a backorder list.

These probably won't last long.

https://www.marlinowners.com/threads/35 ... le.655762/

RP