Spring has sprung. Get out and shoot your Henry
Cleaning corroded cases
Cleaning corroded cases
Hey y’all. I’m looking for ideas to clean the corrosion off of loaded rounds. These 38s have been in a bandolier too long.
I’m leaning toward using my pin tumbler. Risk of water contamination?
I have a couple hundred, so hand polishing is not going to happen. Unless you know of a miracle wipe.
What do you think?
I’m leaning toward using my pin tumbler. Risk of water contamination?
I have a couple hundred, so hand polishing is not going to happen. Unless you know of a miracle wipe.
What do you think?
0 x
Remember, it's not how many guns you have. It's how many bullets you have.
-
- Cowhand
- Posts: 321
- Joined: Thu Jun 09, 2016 11:37 am
- Location: Texas
Re: Cleaning corroded cases
If you have a dry media tumbler (i.e. corn cob or walnut media), I have used that in the past. Some people fear tumbling for too long will break down the gun powder kernels. I usually always use flake or ball pistol powders. YMMV!
Muddy Waters68
Muddy Waters68
1 x
Re: Cleaning corroded cases
You haven't mentioned how difficult it is to wipe or rub it off with some polish. I'd avoid tumbling if you used an extruded powder; which gets broken down by tumbling and exposing uncoated surfaces of the powder. It maybe won't matter though. Also want to avoid immersion with liquid in a pin tumbler.
Safest bet is to get some Brasso brass polish or similar polish or make a slurry of Comet cleanser and watch the ballgame while you clean them up by hand.
You should be done by the third inning! Seriously, hope you find a way to clean them up safely.
Safest bet is to get some Brasso brass polish or similar polish or make a slurry of Comet cleanser and watch the ballgame while you clean them up by hand.
You should be done by the third inning! Seriously, hope you find a way to clean them up safely.
1 x
Re: Cleaning corroded cases
No tumbler. Thanks NHshtr. That may have to work.
0 x
Remember, it's not how many guns you have. It's how many bullets you have.
Re: Cleaning corroded cases
If they are not too rough to the touch, put them in that which they are chambered for, shoot them and then tumble or ultrasonic clean the brass.
3 x
- Vaquero
- Ranch Boss
- Posts: 10418
- Joined: Mon Mar 21, 2016 12:56 am
- Location: Somewhere between Memphis & Nashville
Re: Cleaning corroded cases
I'm with Travlin, just shoot 'em then clean and reload.
RP
RP
1 x
Monte Walsh "You have No idea how little I care".
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
Re: Cleaning corroded cases
They were too sticky to load. I went ahead and ran them through my tumbler. No water, just wet pins. After I was done, it took a good pass with dawn. That cleaned my pins. About 30 minutes per 15 rounds on the cleaning. Not bad results. After shooting, revolver only, they will get a real clean and polish.
4 x
Remember, it's not how many guns you have. It's how many bullets you have.
-
- Cattle Driver
- Posts: 884
- Joined: Sun Dec 11, 2016 10:48 pm
- Location: Spokane WA
Re: Cleaning corroded cases
Do not use the Brasso version that has ammonia. It causes corrosion stress cracking in hard brass. I would have dry vibrated them in walnut media, I never put loaded ammo in a liquid.
https://en.m.wikipedia.org/wiki/Season_cracking
Nickel cases don’t look “cowboy” but OTH they won’t turn nasty in a leather gun belt or butt pad.
John Davies
Spokane WA
https://en.m.wikipedia.org/wiki/Season_cracking
Nickel cases don’t look “cowboy” but OTH they won’t turn nasty in a leather gun belt or butt pad.
John Davies
Spokane WA
0 x
Re: Cleaning corroded cases
Used only pins in minimal water. Was really quite effective. Will see when shooting if water was an issue. Actually, quite hopeful.
0 x
Remember, it's not how many guns you have. It's how many bullets you have.
- JEBar
- Town Marshal / Deputy Admin
- Posts: 19431
- Joined: Sun Mar 20, 2016 10:58 pm
- Location: central NC
Re: Cleaning corroded cases
its been decades since I had to deal with residue from leather belt loops but I vividly recall having to remove it .... hopefully, what you are doing will take care of it .... one thing I do remember is needing to keep a close eye on the cases as time goes on .... a larger than normal percentage of them developed pinhole leaks
4 x