Spring has sprung. Get out and shoot your Henry
Brand new Henry, I marred my lever screw.
- jstanfield103
- Cowhand
- Posts: 379
- Joined: Sat Nov 12, 2016 4:45 pm
- Location: Kentucky
Re: Brand new Henry, I marred my lever screw.
Ahh. the accessorizing begins. You might as well put aside a few dollars for better sights/scope, a nice butt cuff w/cartridge loops, and a matching leather sling and lever wrap. $400-$600 ought to do it . I prefer Diamond D for leather stuff, but there are many others.
ETA: Forgot to mention a SA Revolver and Cowboy rig. And a rifle scabbard for the horse you'll want also.
2 x
Bellum Omnium Contra Omnes is rapidly becoming a reality (11/2023). Para Bellum.
Re: Brand new Henry, I marred my lever screw.
This is a great torque wrench for working on firearms. Available at Amazon but I see them in most of the larger gun shops.
https://www.amazon.com/Wheeler-Accurizi ... 408&sr=8-5
As others have mentioned, leave your regular screwdrivers in the garage and use only gunsmith type screwdrivers on your firearms. The picture above by dave77 showing the flat screwdriver completely filling the slot on the screw is the idea of a gunsmith type screwdriver.
https://www.amazon.com/Wheeler-Accurizi ... 408&sr=8-5
As others have mentioned, leave your regular screwdrivers in the garage and use only gunsmith type screwdrivers on your firearms. The picture above by dave77 showing the flat screwdriver completely filling the slot on the screw is the idea of a gunsmith type screwdriver.
1 x
Re: Brand new Henry, I marred my lever screw.
Update: CS got back to me and said a new screw was on its way! Now that was fast!
2 x
- Shakey Jake
- Drover
- Posts: 4336
- Joined: Wed Aug 16, 2017 11:10 am
- Location: Sugar Land, TX
- Contact:
Re: Brand new Henry, I marred my lever screw.
I also have the Wheeler set. They're really nice for the price!dave77 wrote: ↑Thu May 19, 2022 10:51 pmNot top of the line but decent and has a good selection of flat head bits which is what you want to avoid marring the screw head. You want a bit that is the right width and also the right thickness that also goes to the bottom of the slot.
https://www.amazon.com/Wheeler-Professi ... 126&sr=1-2
Jake
0 x
- markiver54
- Deputy Marshal
- Posts: 10305
- Joined: Sun Nov 04, 2018 11:49 am
- Location: Biue Ridge Mountains, NC
Re: Brand new Henry, I marred my lever screw.
I agree with the Wheeler recommendation. The torque driver is good to have, especially when mounting scope bases and rings.
0 x
I'm your Huckleberry
Re: Brand new Henry, I marred my lever screw.
They probably keep a supply of the various screws on the CS desk. You ain't the first to mangle a screw.
1 x
Bellum Omnium Contra Omnes is rapidly becoming a reality (11/2023). Para Bellum.
Re: Brand new Henry, I marred my lever screw.
I just ordered the Wheeler set. Thanks for the recommendation!
0 x
- BrokenolMarine
- Ranch Foreman
- Posts: 5786
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: Brand new Henry, I marred my lever screw.
A couple other suggestions, if you already know maybe they will help someone else.
Work on a flat surface, with a non slip surface below the firearm. If nothing else, pick up a tool drawer mat and use that, but the gunsmith's mats aren't that expensive and you'll thank yourself in the long run. They keep the gun from slipping, keep screws and or parts from rolling away, and keep you from marring the off side of the gun when you are pressing down on it.
By working on the flat surface and not trying to remove the screws while holding the firearm in your lap, you have WAY more control. Since you have control, and are now using proper screwdrivers, GO SLOW. Apply Slow steady pressure so you aren't surprised when the screw releases. I restart screws by hand, or use a nylon screwdriver so it the screw jumps out or tips the screwdriver doesn't slip and scratch the finish.
Dillon has a handy non-marring tool for prying.. and nudging things in place. I use it a lot on the 1911s and to tuck things into the shotguns and rifles.
https://www.dillonprecision.com/10-8-pe ... 25920.html
I have built my tools up over the years, a few at a time, but they all are necessary. Brass punches are a must for knocking out pins. A small brass / nylon hammer for setting them. No rush, you can build it all up as you go.
The most important thing... Don't rush,
and if you don't know, ask questions, watch videos... but don't guess, and don't force things, either taking them apart or putting them back.
Work on a flat surface, with a non slip surface below the firearm. If nothing else, pick up a tool drawer mat and use that, but the gunsmith's mats aren't that expensive and you'll thank yourself in the long run. They keep the gun from slipping, keep screws and or parts from rolling away, and keep you from marring the off side of the gun when you are pressing down on it.
By working on the flat surface and not trying to remove the screws while holding the firearm in your lap, you have WAY more control. Since you have control, and are now using proper screwdrivers, GO SLOW. Apply Slow steady pressure so you aren't surprised when the screw releases. I restart screws by hand, or use a nylon screwdriver so it the screw jumps out or tips the screwdriver doesn't slip and scratch the finish.
Dillon has a handy non-marring tool for prying.. and nudging things in place. I use it a lot on the 1911s and to tuck things into the shotguns and rifles.
https://www.dillonprecision.com/10-8-pe ... 25920.html
I have built my tools up over the years, a few at a time, but they all are necessary. Brass punches are a must for knocking out pins. A small brass / nylon hammer for setting them. No rush, you can build it all up as you go.
The most important thing... Don't rush,
and if you don't know, ask questions, watch videos... but don't guess, and don't force things, either taking them apart or putting them back.
2 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.