Tube magazine dovetail loose.

[comiskeybum]

Has anyone else had an occurrence where the tube magazine is loose where it dovetails into the barrel at the front of the gun? It moves around slightly left to right in the dovetail but it does not pop out but it is moving around a bit in there I don't remember that occurring when the gun was brand new and I only have about a hundred rounds through it. I'm not sure how big of a deal this is but I wasn't sure if this was common or if there was an easy fix?

All weather 357.

[markiver54]

It's a bit unclear...is the dovetail moving? Or just slight clearance movement when magazine is locked in?
Don't quite understand what you are experiencing.

[comiskeybum]

The actual piece that dovetails into the underside of the barrel is moving left and right when I push on it.

[markiver54]

Sounds like either the dove tail groove was machined too large, which would be a reason to contact Henry Customer Service.
Or, the male piece was not driven in far enough, which would be a quick fix with a brass punch.
Note that dove tail fittings are directional. Can't remember right now which direction tightens, as opposed to removal.
Maybe someone who knows, ( and I know there are many on here ), will chime in with that info. This might be an easy fix for you.

[comiskeybum]

Interesting. I don't have a brass punch, but could buy one if I was confident in using it. Hopefully, someone will chime in and have seen this problem before. Id hate to have to ship the rifle to Henry for something that does not really affect the function of the gun itself. More of a fitting issue.

[brm4450]

Maybe post a picture

[markiver54]

Please don't hold me to this, but I think it is from right to left, as you look down the barrel to tighten. Have no fear though, just be gentle and you can't hurt anything. If you remove the mag tube, you can even use a wooden dowel. Shouldn't take much. A good tap or two should do it.

[markiver54]

C'mon guys...a little help here? What are your thoughts?

[GFK]

Due to recoil, I suspect the movement is not a good thing. Because of warranty, I would probably reach out to Henry, if the solution is not obvious or simple. I do not recall any movement with my loading tube. If so, I would probably be concerned also.

[leverjc]

I haven't had a problem with my magazine tube being loose but have fixed several loose sights by lightly peening the bottom of the sight with a punch to achieve a tighter fit in the dovetail. Always work on the part that goes into the dovetail do not peen the barrel. This might save you the problem of shipping.

[JEBar]

AGREE .... realizing they may not be open for a while, I'd continue to use it while keeping an eye on it .... having dealt with Henry's customer service, I'd get it back to them as quickly as possible ....

[BigAl52]

Ive never done any peeing to a sight base. But I have in the past used some brass shim stock to tighten it up. That also works real well.

[comiskeybum]

I'm shooting a video now and I'll show you guys.

[comiskeybum]

Please watch this video and comment back here

https://youtu.be/7chHQ-37ExE

[JEBar]

interesting video that sure makes it easy to understand the issue .... should you decide to send a link to Henry, please post their response

[Pudsky]

Those two parts don't fit together proper. Looks to me like it needs to go back to Henry. Either the barrel groove is cut too large, or the magazine tube insert is too small. I don't think you should be able to move it around like that with one hand, especially both directions. A punch and hammer should be required.

[comiskeybum]

Starting to think you're right. The guy who did the scope mount offered to look at for me but I sent him the same video and he said "looks like a factory issue, I can take a look but might have to go in."

Blah, I just got the scope mounted, id hate to ship the thing with a scope on it.

[Cofisher]

Yeah, sorry dude. That looks like a new barrel to me. Remove all your add ons and send it back. You will be happy with the results.

[JEBar]

Blah, I just got the scope mounted, id hate to ship the thing with a scope on it.

understood but I believe Henry will want you to remove the scope prior to shipping it back to them ....

[comiskeybum]

UGH. How annoying. I know they will take care of it. I work in customer service for a manufacturer so I totally understand that things like this will happen but man that sucks having just mounted the scope. I will go online and fille out the warranty request form and link them to my video.