NM Blackhawk Range Report
Posted: Thu Jan 21, 2021 3:13 pm
I managed to get some range time to try out the New Model BlackHawk. Since I planned to try both cylinders out, I also took along one of my 1911's to help burn up the 45 ACP ammo.
My first shots with the Ruger were with my 45 Colt loads that I use on the Marlin 1894 Cowboy. These shoot great in the Marlin so I figured I'll give a try in the Blackhawk. I was a little surprised by the recoil of these loads. It was stout. These are a 250 gr coated Missouri Bullets RNFP loaded with 7.0 gr. of Bullseye, with and COL of 1.60". I set my target up at 15 yds. and after settling in, I was able to get some nice 4" 5 shot groups.The groups were about 3" high and 1 1/2" to the right. So after some sight adjustment I was right on target.
Next I switched out the cylinder for the 45 ACP. Swapping cylinders was fast and easy. You can actually swap cylinders faster than reloading the existing one. The first shots with my 45 ACP load, seemed to generate the same recoil as my 1911. Very comfortable and pleasant to shoot. This is a 200 gr coated LSWC bullet with 6.2 gr of Winchester WSF. But the group moved up about 3" from point of aim. I didn't bother to readjust the sight since most likely I will not shoot much 45 ACP from this revolver.
Back home I gave the Blackhawk a good cleaning. It didn't take much to clean. A couple of passes with a good CLP and then some dry patches and the barrel and both cylinders were good to go. Since I'm using coated bullets, there was no signs of lead anywhere. I also had to remove the right side grip panel and round the corner slightly. It was digging into my middle finger between my hand and first joint. Had I fired another 50 rounds I'm sure with would have drawn blood.
Overall I like the way the New Model Blackhawk shoots and handles. This is going to be my favorite companion when I head to the range with my Marlin 1894 Cowboy. My only complaint is the grips are just too small for me.
In the next few weeks I plan to create some new 250 gr. 45 Colt loads with a little less get-up-and-go to them. I'll probably work on a load with Universal since I have a lot on hand and I'm almost out of Bullseye. Also I can see new grips in the near future. Until then I will still have fun.
Paul
My first shots with the Ruger were with my 45 Colt loads that I use on the Marlin 1894 Cowboy. These shoot great in the Marlin so I figured I'll give a try in the Blackhawk. I was a little surprised by the recoil of these loads. It was stout. These are a 250 gr coated Missouri Bullets RNFP loaded with 7.0 gr. of Bullseye, with and COL of 1.60". I set my target up at 15 yds. and after settling in, I was able to get some nice 4" 5 shot groups.The groups were about 3" high and 1 1/2" to the right. So after some sight adjustment I was right on target.
Next I switched out the cylinder for the 45 ACP. Swapping cylinders was fast and easy. You can actually swap cylinders faster than reloading the existing one. The first shots with my 45 ACP load, seemed to generate the same recoil as my 1911. Very comfortable and pleasant to shoot. This is a 200 gr coated LSWC bullet with 6.2 gr of Winchester WSF. But the group moved up about 3" from point of aim. I didn't bother to readjust the sight since most likely I will not shoot much 45 ACP from this revolver.
Back home I gave the Blackhawk a good cleaning. It didn't take much to clean. A couple of passes with a good CLP and then some dry patches and the barrel and both cylinders were good to go. Since I'm using coated bullets, there was no signs of lead anywhere. I also had to remove the right side grip panel and round the corner slightly. It was digging into my middle finger between my hand and first joint. Had I fired another 50 rounds I'm sure with would have drawn blood.
Overall I like the way the New Model Blackhawk shoots and handles. This is going to be my favorite companion when I head to the range with my Marlin 1894 Cowboy. My only complaint is the grips are just too small for me.
In the next few weeks I plan to create some new 250 gr. 45 Colt loads with a little less get-up-and-go to them. I'll probably work on a load with Universal since I have a lot on hand and I'm almost out of Bullseye. Also I can see new grips in the near future. Until then I will still have fun.
- IMG_1866.jpeg (536.91 KiB) Viewed 954 times
Paul