Torque Question

[SoonerShooter]

I have a Big Boy .357 with the brass receiver. I bought the Henry Ring and Base set for it. I know what the torque is for the rings,but I can't find the torque for the 3 screws in the base. I need to know so I don't strip out the receiver. Thanks.

[JEBar]

first, welcome to our forum, delighted to have you join us ..... some of our folks may well know the specs and will be along shortly to provide them .... the most authoritative source for such info would be Henry customer support .... give them a call or send them an email and you'll find they are great to work with .... please take a look at our How Many ? thread (link below) and add your Henry to our community's total


http://henryrifleforums.com/viewtopic.p ... 39#p100039

[markiver54]

FWIW I have the BBS 357, not brass receiver. I set my Fat Wrench at 15-20 inch lbs, w/blue locktite.Have not put tons of rounds through it yet, but that is where I started.

[CT_Shooter]

Welcome to the forum from CT. You'll enjoy the company here.

I have a Big Boy .357 with the brass receiver. I bought the Henry Ring and Base set for it. I know what the torque is for the rings,but I can't find the torque for the 3 screws in the base. I need to know so I don't strip out the receiver. Thanks.

[GunnyGene]

Torque varies depending on whether the threads are "lubed" with something or are dry. Since blue loctite acts as a lubricant initially, you need to know the torque value for a lubed installation. If you tighten per the dry spec, you could easily overtorque the lubed screws. Make sure you ask about this when you contact the Henry techs.

[The Wiz]

Welcome !

[markiver54]

Torque varies depending on whether the threads are "lubed" with something or are dry. Since blue loctite acts as a lubricant initially, you need to know the torque value for a lubed installation. If you tighten per the dry spec, you could easily overtorque the lubed screws. Make sure you ask about this when you contact the Henry techs.

Good point Gunny, I forgot that part.

[Slugnut]

welcome from the welfare state (ny). I do 25 in lbs. an blue loc-tite on steel receivers, I don't know about brass receivers.

[Mags]

.
Welcome to the forum from the TV, Oregon.
The torque spec should have been included on a small piece of installation instruction paper inside the blister package the base came in. It's sandwiched between the front and back of the pretty paper covers inside the blister package. If you just cut the base out of blister package then you may have missed finding the installation sheet.

I have a Big Boy .357 with the brass receiver. I bought the Henry Ring and Base set for it. I know what the torque is for the rings,but I can't find the torque for the 3 screws in the base. I need to know so I don't strip out the receiver. Thanks.

[GunnyGene]

Torque varies depending on whether the threads are "lubed" with something or are dry. Since blue loctite acts as a lubricant initially, you need to know the torque value for a lubed installation. If you tighten per the dry spec, you could easily overtorque the lubed screws. Make sure you ask about this when you contact the Henry techs.

Good point Gunny, I forgot that part.

It probably wouldn't make more than a couple inlbs difference for those tiny little screws, but better safe than sorry. Torque was a very big deal when I was building 747's for Boeing. Besides the lube/dry specs, we also had to be careful about titanium vs. steel fasteners. Sometimes the Engineers would call out steel when they meant Titanium and vice versa, which caused some occasional grief on the line. Especially when there are approx. 2.5 million threaded fasteners on every 747.

[SoonerShooter]

first, welcome to our forum, delighted to have you join us ..... some of our folks may well know the specs and will be along shortly to provide them .... the most authoritative source for such info would be Henry customer support .... give them a call or send them an email and you'll find they are great to work with .... please take a look at our How Many ? thread (link below) and add your Henry to our community's total


http://henryrifleforums.com/viewtopic.p ... 39#p100039

Thanks. I contacted Henry and they replied the next day. The torque is 20 inch pounds for a brass receiver. Thanks again guys.

[SoonerShooter]

.
Welcome to the forum from the TV, Oregon.
The torque spec should have been included on a small piece of installation instruction paper inside the blister package the base came in. It's sandwiched between the front and back of the pretty paper covers inside the blister package. If you just cut the base out of blister package then you may have missed finding the installation sheet.

I have a Big Boy .357 with the brass receiver. I bought the Henry Ring and Base set for it. I know what the torque is for the rings,but I can't find the torque for the 3 screws in the base. I need to know so I don't strip out the receiver. Thanks.

That's what i thought too, but no,it gives the torque value for the rings,but not the base. It just says to check with the gun company for the base torque.

[JEBar]

Thanks. I contacted Henry and they replied the next day. The torque is 20 inch pounds for a brass receiver. Thanks again guys.

not surprised in the least by your reported contact with Henry Customer Service .... they are a top tier company .... glad you now have authoritative info

[Mags]

.
hah! very good. Thanks for sharing that information.

...s. I contacted Henry and they replied the next day. The torque is 20 inch pounds for a brass receiver. Thanks again guys.