Spring has sprung. Get out and shoot your Henry
First reloading question
- Rifletom
- Deputy Marshal
- Posts: 3906
- Joined: Tue Aug 21, 2018 11:26 pm
- Location: California Territory
Re: First reloading question
Yeah, the only bullet I can think of that doesn't have a cannelure I use, is a plated 230gr RN for my 1911 and that is a taper crimp. Everything else does have a cannelure. I crimp in a seperate step as that seems to work for me. Just keep at it Ernie, no need to hurry and the bumps will iron themselves out.
1 x
Re: First reloading question
I have always used a light to medium Lee factory crimp on everything I load and have never had a problem with srt back from recoil.
1 x
- Kissmybrass
- Cattle Driver
- Posts: 594
- Joined: Tue May 04, 2021 1:00 pm
- Location: Issaquah
Re: First reloading question
I'm a huge fan of the Lee factory crimp as well.
1 x
H010G 45-70
H006M Big Boy Classic .357
Sig 320 XCompact
S&W 686 Plus 5"
Rem 870 Tac
H006M Big Boy Classic .357
Sig 320 XCompact
S&W 686 Plus 5"
Rem 870 Tac
Re: First reloading question
Got my things together to load some 357. Set my dies according to lee instructions, set up the powder measure and double checked the drop on digital and beam scale.
Thanks in advance for your help.
Ernie
Sized casing, installed primer then flared casing and dropped powder. Mangled case, too much flair so I raised die and tried again. Set bullet, checked COL (1.588) then crimped.
Guess I am set to try these 5 out. My big question is what do I do with the 2 cases that are damaged and have a primer installed? Thanks in advance for your help.
Ernie
0 x
- Rifletom
- Deputy Marshal
- Posts: 3906
- Joined: Tue Aug 21, 2018 11:26 pm
- Location: California Territory
Re: First reloading question
Put a drop or two of oil in the case then squish case with pliers, toss. From what I can see Ernie, things are looking good. Whats the powder charge?
You have a lot of very good equipment there on your bench. Well done!
You have a lot of very good equipment there on your bench. Well done!
0 x
Re: First reloading question
Thanks for your help!!
11.4 gn 2400.
I have been gathering stuff for a couple years (so it wouldn't hurt too much), until I had the time and space to use it.
11.4 gn 2400.
I have been gathering stuff for a couple years (so it wouldn't hurt too much), until I had the time and space to use it.
0 x
- Rifletom
- Deputy Marshal
- Posts: 3906
- Joined: Tue Aug 21, 2018 11:26 pm
- Location: California Territory
Re: First reloading question
Ernie, where did you get your load info from? And what bullet maker?
0 x
- fortyshooter
- Ranch Foreman
- Posts: 6321
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
Re: First reloading question
Nice setup Ernie especially that Kennedy Toolmaker/Machinist box! I have one just like it....and almost 50 yrs. old!
Do you have a chrono to check bullet speeds? I have a nice collection of loading boo boos too!
Do you have a chrono to check bullet speeds? I have a nice collection of loading boo boos too!
1 x
Re: First reloading question
Got the load information from Lyman as a starting charge and I am using bullets from Berry's.
0 x