Page 1 of 1
Loading 44 mag 245 gr bullets in my big boy
Posted: Mon Jul 19, 2021 6:03 pm
by Johnnyjr
I found out that the 240 gr cast bullets are a little to long to feed thru the action. I'm seating them to the crimp groove. My question is,would it be alright if I shortened the case just enough so they will feed better. I'm talking only a few thousand . ? Thanks for your advice.John
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Mon Jul 19, 2021 7:26 pm
by fortyshooter
What is your COL? I shoot the Missouri Bullets 240 gr. SWC bullet seated at 1.600-1.605 and they feed fine in my Henry Carbine.
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Mon Jul 19, 2021 8:38 pm
by BigAl52
What Forty says what the OAL length and have you tried them in your gun
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Mon Jul 19, 2021 8:54 pm
by Rifletom
I wouldn't shorten the cases. You may have to trim to SAMMI length[once], but don't shorten them. There seems to be another issue at hand here.
We'll help you get this figured out.
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Mon Jul 19, 2021 10:12 pm
by Vaquero
I agree with the others, I have cycled some 320+ gr cast through mine with no problem.
RP
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Tue Jul 20, 2021 8:33 am
by Johnnyjr
I'm not sure where I even got these 240 swc from. But they were a bit to long to feed thru the Henry. Just out of curiosity,it took 15 thousands of one case. Seated the bullet and it fed great. No problem. I don't see where this will be an issue, except to keep the cases all in the same box.. I'll have to try to find out where I got them from.
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Tue Jul 20, 2021 10:40 am
by BigAl52
Sounds strange to me. I have never run into a 240gr swc with a crimp groove that would make a round to long to run in 44 mag. If you trim all your cases .015 you probably now are going to have some cases that are shorter than they should be.
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Tue Jul 20, 2021 11:20 am
by Johnnyjr
Haven't only done one of them. But,like I'm saying they will not feed. After doing some research,I have found a few articles about the same thing. Especially with 357 lever guns..
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Tue Jul 20, 2021 2:01 pm
by Rifletom
BigAl52 wrote: ↑Tue Jul 20, 2021 10:40 am
Sounds strange to me. I have never run into a 240gr swc with a crimp groove that would make a round to long to run in 44 mag. If you trim all your cases .015 you probably now are going to have some cases that are shorter than they should be.
...and possibly resulting in over pressure loads. I wouldn't shorten them. There is something else at play here.
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Wed Jul 21, 2021 1:44 pm
by Johnnyjr
Your right. The bullet is to darn long.lol
Re: Loading 44 mag 245 gr bullets in my big boy
Posted: Wed Jul 21, 2021 8:23 pm
by BigAl52
Pictures would help of the bullet itself. Also whats the COL when you load one without trimming