Spring has sprung. Get out and shoot your Henry
Wrangler Holster
- BrokenolMarine
- Ranch Foreman
- Posts: 5802
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Wrangler Holster
Some of you may remember the pouch I made for .22s so I could wander around the farm and plink.
It was always my intention to make an accompanying holster for the Ruger Wrangler .22 to go along with that pouch. A knock around gun in case we came across a varmint, an evil Tin Can that needed shootin'; whatever. The dreadful triple digit heat and some other medical issues have kept me from it, but I have been out in the shop every couple days playing with the design, especially after seeing a fellow leatherworker show off a nice holster project recently.
My first shot went well, to start. I got the holster cut out and the test "fold" looked good. I laid out the area for tooling and got started. My Gimp hand started to hurt after the cutting out and layout but I thought I could finish the basket weave. A mistake. It got away from me. Nope. I put it aside and quit for the day. Note the loss of the pattern.
It's okay, I had stamped this version with my new maker's mark stamp and applied a bit too much force in my stroke blurring the lettering.
Guess I'll strike a tad lighter in the next application. It should read: "BrokenolMarine" if I hadn't blurred it.
I had appointments the next day, so the day after I recut the pattern. I took my time and then laid 'er out again. Then quit for the day. I came out the next morning and tooled HALF the basketweave and quit. Tooled the rest the following day. I was pleased with that.
I went out this morning and tossed the rough strap I had cut out, and using an old high end gunbelt strap as a template, I cut out a new strap, adapting the length to fit my needs, placing holes where I needed them, and then tooling the strap to accent my pattern. I was pretty happy with it.
Here is the Ruger Wrangler laid on the rough.
There is still quite a bit to do. I'll have to line the holster to protect the gun from the hardware, finish the edges of the strap and the holster, make and sew the belt loop on the back, after deciding on cross draw or strong side. Yup, lots to do. I'll dye the holster and strap before most of the above....
Busy.. beats zoning in the recliner.
It was always my intention to make an accompanying holster for the Ruger Wrangler .22 to go along with that pouch. A knock around gun in case we came across a varmint, an evil Tin Can that needed shootin'; whatever. The dreadful triple digit heat and some other medical issues have kept me from it, but I have been out in the shop every couple days playing with the design, especially after seeing a fellow leatherworker show off a nice holster project recently.
My first shot went well, to start. I got the holster cut out and the test "fold" looked good. I laid out the area for tooling and got started. My Gimp hand started to hurt after the cutting out and layout but I thought I could finish the basket weave. A mistake. It got away from me. Nope. I put it aside and quit for the day. Note the loss of the pattern.
It's okay, I had stamped this version with my new maker's mark stamp and applied a bit too much force in my stroke blurring the lettering.
Guess I'll strike a tad lighter in the next application. It should read: "BrokenolMarine" if I hadn't blurred it.
I had appointments the next day, so the day after I recut the pattern. I took my time and then laid 'er out again. Then quit for the day. I came out the next morning and tooled HALF the basketweave and quit. Tooled the rest the following day. I was pleased with that.
I went out this morning and tossed the rough strap I had cut out, and using an old high end gunbelt strap as a template, I cut out a new strap, adapting the length to fit my needs, placing holes where I needed them, and then tooling the strap to accent my pattern. I was pretty happy with it.
Here is the Ruger Wrangler laid on the rough.
There is still quite a bit to do. I'll have to line the holster to protect the gun from the hardware, finish the edges of the strap and the holster, make and sew the belt loop on the back, after deciding on cross draw or strong side. Yup, lots to do. I'll dye the holster and strap before most of the above....
Busy.. beats zoning in the recliner.
7 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- North Country Gal
- Firearms Advisor
- Posts: 6094
- Joined: Thu Apr 07, 2016 12:46 pm
- Location: northern Wisconsin
Re: Wrangler Holster
Can't wait to see the finished product, Marine, as well as a range report on the Wrangler. Keep us posted.
0 x
- markiver54
- Deputy Marshal
- Posts: 10307
- Joined: Sun Nov 04, 2018 11:49 am
- Location: Biue Ridge Mountains, NC
Re: Wrangler Holster
Nice work Jim! As NCG said...looking forward to the finished project.
0 x
I'm your Huckleberry
Re: Wrangler Holster
That’s a very nice looking holster! I like the Wranglers too. Carry permits are very hard to get here, so I have little to no use for handguns anymore, or I’d have a Wrangler and likely a Vaquero as well.
0 x
SGC .22 LR Stripped and oiled up
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
- daytime dave
- Administrator / Owner
- Posts: 4830
- Joined: Sun Mar 20, 2016 10:27 pm
- Location: Upstate NY
Re: Wrangler Holster
Beautiful leather work Marine! Your work is very nice. Great idea to take a .22 along on trips around the property "just in case" .
0 x
Some days I'm Andy, most days I'm Barney........
Eaglescout, NRA Life Endowment member, BCCI Life Member
Eaglescout, NRA Life Endowment member, BCCI Life Member
- fortyshooter
- Ranch Foreman
- Posts: 6307
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
- BrokenolMarine
- Ranch Foreman
- Posts: 5802
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: Wrangler Holster
While I was in the shop working on the Rifle Rest, I worked on the Wrangler Holster again. I formed the belt loop for the back of the holster. This entails cutting out the shape then wet forming it over a scrap piece of belt the right size.
After that I burnished ALL the edges. The holster, strap edges, and the belt Loop edges. You dampen the edges and apply Japanese burnishing gum, and buff lightly with a burnishing tool. You can even use a screwdriver handle, or the shaft of one. It's not about pressure but friction. Burnishing seals the edges of the leather grain to keep out the dirt and moisture that can cause the leather to peel apart with use.
Once everything dries and sets, I'll sew down the belt loop, attach the tie down to the back with the Chicago Screw, and screw on the stud on the front side. Then it will be time to glue in the lining. After trimming everything , I'll antique the panel and strap. Then I can sew up the holster. Once that's done, I can put on the final finish. She'll be done and ready to use. It should match up with the 22 ammo pouch rather nicely.
After that I burnished ALL the edges. The holster, strap edges, and the belt Loop edges. You dampen the edges and apply Japanese burnishing gum, and buff lightly with a burnishing tool. You can even use a screwdriver handle, or the shaft of one. It's not about pressure but friction. Burnishing seals the edges of the leather grain to keep out the dirt and moisture that can cause the leather to peel apart with use.
Once everything dries and sets, I'll sew down the belt loop, attach the tie down to the back with the Chicago Screw, and screw on the stud on the front side. Then it will be time to glue in the lining. After trimming everything , I'll antique the panel and strap. Then I can sew up the holster. Once that's done, I can put on the final finish. She'll be done and ready to use. It should match up with the 22 ammo pouch rather nicely.
2 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5802
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: Wrangler Holster
Back out, and stained the back of the strap, and the belt loop brown for contrast. Added a second maker's mark to the loop.
Then glued the belt loop in place with contact cement and clamped it to let it set up. Once that is done I'll stitch it in place.
Slowly but surely. This thing may not be perfect, but it's a learning experience. The next one will have inlays, and be for the Birds Head .357 with a matching belt and knife sheath. THAT will be a project I'll enjoy.
Then glued the belt loop in place with contact cement and clamped it to let it set up. Once that is done I'll stitch it in place.
Slowly but surely. This thing may not be perfect, but it's a learning experience. The next one will have inlays, and be for the Birds Head .357 with a matching belt and knife sheath. THAT will be a project I'll enjoy.
0 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5802
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: Wrangler Holster
Went out this morning after breakfast to work on the holster. Took it out of the clamps and slipped a belt scrap in the loop and set up the Cowboy machine. I took a deep breath and sewed down the edges of the loop. I took my time, sewed at the slowest rate the machine would go and was really happy that all my practice had paid off.
Time to cut off the Irish Pennants, as we called them in the Corps. Some call them tag ends. I guess with Cancel Culture these days, Irish Pennants would be "Wrong." I'm Scots-Irish and Indian.. and not offended, but ... I added a handy little battery powered tool to the drawer not too long ago. Works great. A cauterizing tool. Cuts and burns the thread ends at the same time.
I am very pleased with the way this turned out. NOT perfect, but a lot better than previous attempts and practice runs. I hope when I sew the holster together it looks as good.
I coated the finished sides of the leather with a top coat, to put a barrier between the leather and the antiquing to come. That way the excess will wipe off clean. Left it to dry. When I go out in an hour or so the final look will start to show. I'll antique it, then wipe it and get the look I want and leave it to dry. When I go back out I'll put on the finish, and leave it to dry again. Then when I come back out I'll glue in the lining.
Time to cut off the Irish Pennants, as we called them in the Corps. Some call them tag ends. I guess with Cancel Culture these days, Irish Pennants would be "Wrong." I'm Scots-Irish and Indian.. and not offended, but ... I added a handy little battery powered tool to the drawer not too long ago. Works great. A cauterizing tool. Cuts and burns the thread ends at the same time.
I am very pleased with the way this turned out. NOT perfect, but a lot better than previous attempts and practice runs. I hope when I sew the holster together it looks as good.
I coated the finished sides of the leather with a top coat, to put a barrier between the leather and the antiquing to come. That way the excess will wipe off clean. Left it to dry. When I go out in an hour or so the final look will start to show. I'll antique it, then wipe it and get the look I want and leave it to dry. When I go back out I'll put on the finish, and leave it to dry again. Then when I come back out I'll glue in the lining.
2 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.