Spring has sprung. Get out and shoot your Henry
Anyone Handled the Mossberg Shockwave?
Re: Anyone Handled the Mossberg Shockwave?
My brother was a Remington 870 guy while I always shot a Winchester 1300.
They're all pretty good but we do have our personal favorites. That 1300 was stone reliable, fed everything and had a slick action. I gave a Mossberg to my kid for his birthday, I like them just fine. The Mossbergs have really caught on in modern times, lots of accessories available and they're good guns at good prices.
They're all pretty good but we do have our personal favorites. That 1300 was stone reliable, fed everything and had a slick action. I gave a Mossberg to my kid for his birthday, I like them just fine. The Mossbergs have really caught on in modern times, lots of accessories available and they're good guns at good prices.
0 x
- BrokenolMarine
- Ranch Foreman
- Posts: 5818
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: Anyone Handled the Mossberg Shockwave?
I ordered a sling swivel for my Shockwave and it came in this evening. Installation would have taken about three minutes, but I took the time to take pictures, so I could share it with ya'll. This is the GG&G Quick Release single point side sling mount. Just what I was looking for.
To get started, I first insured the firearm was unloaded, the chamber was clear, and I had the tools I needed on hand. Proper sized punch, blue loc-tite, and the parts kit which included the allen wrench, plastic pads, the receiver for the quick release sling swivel and the screw that will replace the trigger retaining pin. Here is a close up peek at the kit. The first step was to knock out the trigger retaining pin. I used a proper sized punch, and a light tap with a nylon hammer. No problem at all. Since my memory is VERY short I forgot to take a picture of the next step, but the whole process is easy as pie. Without pulling on the trigger assembly, I put the smaller of the two plastic guards on the screw and inserted it from the right side, since I am right handed and wanted the sling swivel on the left. Another light tap with the nylon mallet seated the screw.
I put the larger of the plastic guards over the screw on the left side, readying the screw to receive the swivel base. I put a couple drops of Loc-tight in the threads of the base and lightly screwed it in place until it contacted the plastic guard. For aesthetics, I turned the logo UP. I then used the allen key to turn the screw from the right side a 1/2 turn to draw the assembly tight, but not TOO tight. I worked the action to insure the bolt functioned smoothly. If the base assembly is too tight it will flex the aluminum receiver and bind the bolt. If this happens, loosen the screw 1/4 turn and try again. Do this BEFORE the loc-tight sets.
Now test the quick release swivel. I always mark and save any parts removed... I plan to use a single point sling, and it worked out perfectly.
Fits well and detaches with a pop of the button. No permanent changes to the firearm and swapping back to the original setup would take about two minutes. If I remember where I stored the dang pin when the time comes. (That's why I have a large tupperware storage bin with all the gun parts stored in there. It's a matter of digging thru and finding that small bag among all the parts.)
To get started, I first insured the firearm was unloaded, the chamber was clear, and I had the tools I needed on hand. Proper sized punch, blue loc-tite, and the parts kit which included the allen wrench, plastic pads, the receiver for the quick release sling swivel and the screw that will replace the trigger retaining pin. Here is a close up peek at the kit. The first step was to knock out the trigger retaining pin. I used a proper sized punch, and a light tap with a nylon hammer. No problem at all. Since my memory is VERY short I forgot to take a picture of the next step, but the whole process is easy as pie. Without pulling on the trigger assembly, I put the smaller of the two plastic guards on the screw and inserted it from the right side, since I am right handed and wanted the sling swivel on the left. Another light tap with the nylon mallet seated the screw.
I put the larger of the plastic guards over the screw on the left side, readying the screw to receive the swivel base. I put a couple drops of Loc-tight in the threads of the base and lightly screwed it in place until it contacted the plastic guard. For aesthetics, I turned the logo UP. I then used the allen key to turn the screw from the right side a 1/2 turn to draw the assembly tight, but not TOO tight. I worked the action to insure the bolt functioned smoothly. If the base assembly is too tight it will flex the aluminum receiver and bind the bolt. If this happens, loosen the screw 1/4 turn and try again. Do this BEFORE the loc-tight sets.
Now test the quick release swivel. I always mark and save any parts removed... I plan to use a single point sling, and it worked out perfectly.
Fits well and detaches with a pop of the button. No permanent changes to the firearm and swapping back to the original setup would take about two minutes. If I remember where I stored the dang pin when the time comes. (That's why I have a large tupperware storage bin with all the gun parts stored in there. It's a matter of digging thru and finding that small bag among all the parts.)
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
Re: Anyone Handled the Mossberg Shockwave?
I haven’t shot the Shockwave but in my local Florida Gun forums many people are re-selling them and I have seen them for as low as $275/$300.
My choice for HD is a Remington 870 Marine Magnum with a 18 inch barrel.
My choice for HD is a Remington 870 Marine Magnum with a 18 inch barrel.
0 x
Si vis pacem, para bellum!
H006M; H006MR; H001T; H004; another H001T
H006M; H006MR; H001T; H004; another H001T
- JEBar
- Town Marshal / Deputy Admin
- Posts: 19382
- Joined: Sun Mar 20, 2016 10:58 pm
- Location: central NC
Re: Anyone Handled the Mossberg Shockwave?
thanks for taking the time and effort to record and post the pictures along with your comments ....
0 x
Re: Anyone Handled the Mossberg Shockwave?
Great write up BoM. I agree with the reasons you chose the Mossberg. Two reasons I like Mossberg shotguns are the safety location and slide release, although the slide release won’t come in to play on my new semi auto. The safety is in the most natural spot.
0 x
SGC .22 LR Stripped and oiled up
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
Re: Anyone Handled the Mossberg Shockwave?
Same for me.Redthies wrote: ↑Thu Jun 20, 2019 10:30 amGreat write up BoM. I agree with the reasons you chose the Mossberg. Two reasons I like Mossberg shotguns are the safety location and slide release, although the slide release won’t come in to play on my new semi auto. The safety is in the most natural spot.
I grew up with a Mossberg 500 12ga and I just can't get used to any safety that's not on the tang.
Seems like the most natural placement, but I'm sure that's just what I'm used to.
For those reasons, and just because I'm a Mossy fan, I bought the Shockwave.
I purchased the .410bore model, but plan on adding all three flavors to the herd.
I bought the .410 first because I found it on sale for a decent price, and because I thought it would be the harder of the three to locate.
I'll buy the 12ga and 20ga as the come available, and as funds allow.
I already have the model 500 in 12ga, 20ga, and .410bore so the Shockwaves are just adding to the collection.
0 x
Re: Anyone Handled the Mossberg Shockwave?
I think the .410 version would sell the least, but would make an awesome “hey there’s dinner” gun for in the pickup. We have grouse everywhere here and that would slay them nicely!
0 x
SGC .22 LR Stripped and oiled up
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
Re: Anyone Handled the Mossberg Shockwave?
Oh, and @BrokenolMarine: I have the exact same hammer on my workbench. It’s been going strong for close to 20 years!
0 x
SGC .22 LR Stripped and oiled up
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
BBSC .357 w Skinner Express & Patridge
BBSC .44 Magnum with Skinners
Marlin 1895GS .45-70 w RPP Cloverleaf
Marlin 336BL .30-30 w Skinner LoPro 2 and Sig 2-7x
1912 Winchester 1894 .30 WCF
Re: Anyone Handled the Mossberg Shockwave?
New addition to my Shockwave, nice 6 shot shell holder with a Picatinny rail. I have the model with the laser so had to get some longer mounting screws. Had already added the light, just need a sling and holder like BrokenolMarine put on his and I'll be done.
Darn, just realized I need to get something to put on the new Picatinny rail.
Darn, just realized I need to get something to put on the new Picatinny rail.
0 x