Spring has sprung. Get out and shoot your Henry
Henry Big Boy Steel .44 Magnum Journey
- Goodbye Middle Class
- Wrangler
- Posts: 56
- Joined: Wed Apr 08, 2020 6:02 pm
Re: Henry Big Boy Steel .44 Magnum Journey
.
Dressing the rifle with the RLO leather was super easy, then kind of a pain in the behind......
The strap and bandolier were a snap. The swivels, with a drop of oil, fit perfectly into the Henry factory swivel studs
The stock cover took a little more patience. The leather laces will break if pulled too hard. The challenge is getting it tight enough pull/stretching the leather a bit to get a tight fit. The sleeve, naturally, wants to ride forward to the narrower end of the stock. The swivel stud gives an anchor point to prevent this. I did, however, adjust it once I had it on. I pulled one of the laces, stretching back even further back over the stud to add additional tension. This looks a little less symmetrical but prevents any slide forward or rotation around the wood stock.
The real pain in the butt was the lever loop wrap. This is what took the real patience. My pictures show my solution. I would recommend DO NOT do it this way with the lever still on the rifle and the rifle in the gun vise. Lesson learned!
Next time, definitely use the clamps, but I will remove the lever from the rifle, wrap the internal end of the lever loop in scrap leather and lock it in a traditional vise. This would have made it so much easier for me to work the leather around the loop. Don't be a dummy like me the first time I tried this.
I would also recommend having clamps. I have small ones from other hobbies and woodworking. They helped keep each few laces tight while I threaded the next 4 or 5. Then moved the clamps along as I went. Definitely have some type of a leather work needle. I made my own using some scrap electrical wire. This will be necessary to thread the laces which is made from some type of sinew or intestine? It is super strong, has a small amount of stretch, and is a little greasy.
I think the contrast looks nice on the brown leather but on the black it was a little much for my preference. So I touched up the loop laces with a sharpie to black them out. The sinew absorbed it nicely. I gave it some time to dry then wiped with a paper towel to make sure it didn't transfer off. I think next time I will blacken the sinew before threading for a better uniformity of appearance.
Overall, I'm very pleased with how it turned out!
Enjoy!
.....more to come..........
.
Dressing the rifle with the RLO leather was super easy, then kind of a pain in the behind......
The strap and bandolier were a snap. The swivels, with a drop of oil, fit perfectly into the Henry factory swivel studs
The stock cover took a little more patience. The leather laces will break if pulled too hard. The challenge is getting it tight enough pull/stretching the leather a bit to get a tight fit. The sleeve, naturally, wants to ride forward to the narrower end of the stock. The swivel stud gives an anchor point to prevent this. I did, however, adjust it once I had it on. I pulled one of the laces, stretching back even further back over the stud to add additional tension. This looks a little less symmetrical but prevents any slide forward or rotation around the wood stock.
The real pain in the butt was the lever loop wrap. This is what took the real patience. My pictures show my solution. I would recommend DO NOT do it this way with the lever still on the rifle and the rifle in the gun vise. Lesson learned!
Next time, definitely use the clamps, but I will remove the lever from the rifle, wrap the internal end of the lever loop in scrap leather and lock it in a traditional vise. This would have made it so much easier for me to work the leather around the loop. Don't be a dummy like me the first time I tried this.
I would also recommend having clamps. I have small ones from other hobbies and woodworking. They helped keep each few laces tight while I threaded the next 4 or 5. Then moved the clamps along as I went. Definitely have some type of a leather work needle. I made my own using some scrap electrical wire. This will be necessary to thread the laces which is made from some type of sinew or intestine? It is super strong, has a small amount of stretch, and is a little greasy.
I think the contrast looks nice on the brown leather but on the black it was a little much for my preference. So I touched up the loop laces with a sharpie to black them out. The sinew absorbed it nicely. I gave it some time to dry then wiped with a paper towel to make sure it didn't transfer off. I think next time I will blacken the sinew before threading for a better uniformity of appearance.
Overall, I'm very pleased with how it turned out!
Enjoy!
.....more to come..........
.
You do not have the required permissions to view the files attached to this post.
Last edited by Goodbye Middle Class on Sun May 02, 2021 8:33 am, edited 7 times in total.
2 x
- JEBar
- Town Marshal / Deputy Admin
- Posts: 19346
- Joined: Sun Mar 20, 2016 10:58 pm
- Location: central NC
Re: Henry Big Boy Steel .44 Magnum Journey
well thought out and executed .... nice work indeed .... the thought of using clamps like that would have never crossed my mind ..
1 x
- markiver54
- Deputy Marshal
- Posts: 10306
- Joined: Sun Nov 04, 2018 11:49 am
- Location: Biue Ridge Mountains, NC
Re: Henry Big Boy Steel .44 Magnum Journey
Congrats on a job well done!
Looks great too!
Looks great too!
1 x
I'm your Huckleberry
- Goodbye Middle Class
- Wrangler
- Posts: 56
- Joined: Wed Apr 08, 2020 6:02 pm
Re: Henry Big Boy Steel .44 Magnum Journey
.
Last post for the day.....
Around the same time I purchased the Rifle I also picked up a little partner for it in the same caliber.......
A sweet compliment to the rifle and handy "Bear Repellent".
It's an Awesome Performer, Wicked accurate, reasonable recoil, and a pleasure to shoot.
.
Last post for the day.....
Around the same time I purchased the Rifle I also picked up a little partner for it in the same caliber.......
A sweet compliment to the rifle and handy "Bear Repellent".
It's an Awesome Performer, Wicked accurate, reasonable recoil, and a pleasure to shoot.
.
You do not have the required permissions to view the files attached to this post.
Last edited by Goodbye Middle Class on Sat Jul 18, 2020 5:34 pm, edited 1 time in total.
0 x
- markiver54
- Deputy Marshal
- Posts: 10306
- Joined: Sun Nov 04, 2018 11:49 am
- Location: Biue Ridge Mountains, NC
Re: Henry Big Boy Steel .44 Magnum Journey
Very very nice!!
Love wheel guns. Especially S&W's I have two. A 6" 686 and an 8 3/8 500 mag.
Love wheel guns. Especially S&W's I have two. A 6" 686 and an 8 3/8 500 mag.
0 x
I'm your Huckleberry
- Goodbye Middle Class
- Wrangler
- Posts: 56
- Joined: Wed Apr 08, 2020 6:02 pm
Re: Henry Big Boy Steel .44 Magnum Journey
Having had some time to pop off several brands I've settled on the Hornady Custom XTP 240gr JHPs.
Plenty of other sources for ballistics info. I just decided what I liked. I figure the Hornady factory rounds are hot enough and consistent loads. I won't be loading any of my own so for the price I'm happy with these. They seem to be cleaner firing as well. (I went through a cheapie box of cowboy loads, forget which brand. They were fun plinkers, but some dirty barrel-puffers for sure.)
The jacketed rounds also cycled smoothly and I managed decent accuracy with them too.
More out of curiosity, than anything, I tried the Leverevolution .225gr also from Hornady.
I didn't find much difference other than the lighter bullet kick. I'll use up what I have at the range and then stick with the XTP 240gr for both the Henry and S&W.
I picked up a .30 cal steel man-purse to carry my "stuff".
The boxes fit nicely inside.....
That's all for now.
Next couple of posts will have a lot more, being a tale of trial and error as I finally worked out my scope and rail situation...
Plenty of other sources for ballistics info. I just decided what I liked. I figure the Hornady factory rounds are hot enough and consistent loads. I won't be loading any of my own so for the price I'm happy with these. They seem to be cleaner firing as well. (I went through a cheapie box of cowboy loads, forget which brand. They were fun plinkers, but some dirty barrel-puffers for sure.)
The jacketed rounds also cycled smoothly and I managed decent accuracy with them too.
More out of curiosity, than anything, I tried the Leverevolution .225gr also from Hornady.
I didn't find much difference other than the lighter bullet kick. I'll use up what I have at the range and then stick with the XTP 240gr for both the Henry and S&W.
I picked up a .30 cal steel man-purse to carry my "stuff".
The boxes fit nicely inside.....
That's all for now.
Next couple of posts will have a lot more, being a tale of trial and error as I finally worked out my scope and rail situation...
You do not have the required permissions to view the files attached to this post.
Last edited by Goodbye Middle Class on Wed Aug 19, 2020 1:20 pm, edited 1 time in total.
1 x
Re: Henry Big Boy Steel .44 Magnum Journey
It is amazing just how many additional purchases a new rifle leads to.
I have had a BB brass my son purchased in March sitting in the safe unfired, with covid and restrictions in place he hasnt been able to get home from his posting. Waiting for him to home and be the first to fire it.
So far I have added
200 factory ammo
200 starline brass
2k LP primers
310gr 6 cavity mould
210gr 2 cavity mould
4 MTM ammo boxes
240, 270 & 300gr jacketed bullets
shot capsuals
base & rings
2-7x scope
With him on standby for deployment overseas it could be a while before he is home. The way I am going I will have spent more than he did on the rifle
I have had a BB brass my son purchased in March sitting in the safe unfired, with covid and restrictions in place he hasnt been able to get home from his posting. Waiting for him to home and be the first to fire it.
So far I have added
200 factory ammo
200 starline brass
2k LP primers
310gr 6 cavity mould
210gr 2 cavity mould
4 MTM ammo boxes
240, 270 & 300gr jacketed bullets
shot capsuals
base & rings
2-7x scope
With him on standby for deployment overseas it could be a while before he is home. The way I am going I will have spent more than he did on the rifle
3 x
- Goodbye Middle Class
- Wrangler
- Posts: 56
- Joined: Wed Apr 08, 2020 6:02 pm
Re: Henry Big Boy Steel .44 Magnum Journey
220 wrote: ↑Wed Aug 19, 2020 12:51 amIt is amazing just how many additional purchases a new rifle leads to.
I have had a BB brass my son purchased in March sitting in the safe unfired, with covid and restrictions in place he hasnt been able to get home from his posting. Waiting for him to home and be the first to fire it.
So far I have added
200 factory ammo
200 starline brass
2k LP primers
310gr 6 cavity mould
210gr 2 cavity mould
4 MTM ammo boxes
240, 270 & 300gr jacketed bullets
shot capsuals
base & rings
2-7x scope
With him on standby for deployment overseas it could be a while before he is home. The way I am going I will have spent more than he did on the rifle
I agree. Hilarious because it is so true!
Not to mention all the never used accessories I'll have to resell somewhere. I experimented with a lot of different options when I was trying to figure out how to mount the scout scope I wanted. Often with comedic results.
I even tried an AR style cantilever mount which absurdly resulted in this Horror Show!!!
Hahahahahahaha! I laugh out loud every time I think about how ridiculously goofy this looked!
I'll have more to come about that part of my journey in the next few posts.....
You do not have the required permissions to view the files attached to this post.
1 x
- Goodbye Middle Class
- Wrangler
- Posts: 56
- Joined: Wed Apr 08, 2020 6:02 pm
Re: Henry Big Boy Steel .44 Magnum Journey
I decided I definitely wanted a scout scope. I figured with a pistol cartridge rifle I would not be comfortable taking more than a 100-150 yard maximum shot. No desire to be dropping Al-Qaeda at 700 yards so no need for a high powered scope.
I just wanted a fixed power, quick acquisition scope that I could ready-raise for an accurate shot that also had comfortable eye relief. After research and reviews I decided on the
Leupold FX-II Scout IER 2.5x28mm Scope.
So here's the rub....how the heck am I supposed to mount a scout scope when nobody (and I mean nobody) makes a manufacturer ready scout rail for a Henry Big Boy Steel??!!
Well that's when picked up more than a few rail/ring/mount options to experiment with.....
Also picked up some Leupold lense covers.
These are correct, but a word of warning: some sites don't have accurate info on part number compatibility based on scope model. The first time ordered I discovered the front lense cover they said was a match...was not. Had to send back, do research and order the right one. Annoying!
I would recommend going to Leupold's site for accurate part numbers before you order.
I just wanted a fixed power, quick acquisition scope that I could ready-raise for an accurate shot that also had comfortable eye relief. After research and reviews I decided on the
Leupold FX-II Scout IER 2.5x28mm Scope.
So here's the rub....how the heck am I supposed to mount a scout scope when nobody (and I mean nobody) makes a manufacturer ready scout rail for a Henry Big Boy Steel??!!
Well that's when picked up more than a few rail/ring/mount options to experiment with.....
Also picked up some Leupold lense covers.
These are correct, but a word of warning: some sites don't have accurate info on part number compatibility based on scope model. The first time ordered I discovered the front lense cover they said was a match...was not. Had to send back, do research and order the right one. Annoying!
I would recommend going to Leupold's site for accurate part numbers before you order.
You do not have the required permissions to view the files attached to this post.
2 x