Spring has sprung. Get out and shoot your Henry
Made up a speed loader for .357 today !
- fortyshooter
- Ranch Foreman
- Posts: 6297
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
Made up a speed loader for .357 today !
Had some 1/2 SharkBite tube in the shop which measures .625 on O.D. and went to work. Cut length to 16 5/8 inch for 10 rounds
Machined one end back about 1/2 inch to a .560 diameter so it would slip into mag tube. Used a plastic 1/2 inch plug to plug one end and pinned it in place.
Then drill hole near feed end of tube for 1/2 inch Hitch Pin Clip. Add a small chain or whatever handy and secure to tube in a slightly machined groove, a small cable tie that secures chain. Cable tie won't slide up and down being secured in groove.
Machined one end back about 1/2 inch to a .560 diameter so it would slip into mag tube. Used a plastic 1/2 inch plug to plug one end and pinned it in place.
Then drill hole near feed end of tube for 1/2 inch Hitch Pin Clip. Add a small chain or whatever handy and secure to tube in a slightly machined groove, a small cable tie that secures chain. Cable tie won't slide up and down being secured in groove.
You do not have the required permissions to view the files attached to this post.
7 x
- fortyshooter
- Ranch Foreman
- Posts: 6297
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
Re: Made up a speed loader for .357 today !
.
There ya go! And somebody a few weeks ago downplayed using PEX pipe. Nice job.
There ya go! And somebody a few weeks ago downplayed using PEX pipe. Nice job.
0 x
UPDATES: OR passes 114, "one of strictest gun control measures in U.S." https://henryrifleforums.com/viewtopic. ... 34#p213234
Re: Made up a speed loader for .357 today !
Nice job Forty. Those Rifletom 180's will be goin in as fast as there comin out.
1 x
Don't worry about getting older and still doing stupid stuff. You'll do the stupid stuff as always, only much slower. Hold my beer and watch this.......
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
- Vaquero
- Ranch Boss
- Posts: 10316
- Joined: Mon Mar 21, 2016 12:56 am
- Location: Somewhere between Memphis & Nashville
Re: Made up a speed loader for .357 today !
Great job.
Good one Al.
RP
Good one Al.
RP
0 x
Monte Walsh "You have No idea how little I care".
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
Re: Made up a speed loader for .357 today !
Forty you should offer some of those for sale in the classifieds. You might sell a few. Its a great idea I think
1 x
Don't worry about getting older and still doing stupid stuff. You'll do the stupid stuff as always, only much slower. Hold my beer and watch this.......
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
- markiver54
- Deputy Marshal
- Posts: 10305
- Joined: Sun Nov 04, 2018 11:49 am
- Location: Biue Ridge Mountains, NC
Re: Made up a speed loader for .357 today !
Looks great Forty! Might follow your instructions as best I can and attempt to make one.
What method did you use to machine the 1/2 inch area and the groove?
What method did you use to machine the 1/2 inch area and the groove?
0 x
I'm your Huckleberry
- fortyshooter
- Ranch Foreman
- Posts: 6297
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
Re: Made up a speed loader for .357 today !
Well that was a lathe job. Going to the range today to try the speed loaders out and also my rear sight mod.markiver54 wrote: ↑Sun Jan 26, 2020 10:58 amLooks great Forty! Might follow your instructions as best I can and attempt to make one.
What method did you use to machine the 1/2 inch area and the groove?
I'm out of the 40 180 gr. rounds I loaded up....had too much fun with them! But have some 158's and others to try.
Need to get more .357 Mag brass since I never had more than 100 rounds of those.
You do not have the required permissions to view the files attached to this post.
0 x