Spring has sprung. Get out and shoot your Henry
Magazine Tube Replacement
Re: Magazine Tube Replacement
OP mentioned in a post on a different thread about this subject he had returned the rifle and bought a BLR.
0 x
Re: Magazine Tube Replacement
I did not realize Henry had changed the forward end of the load tube by modifying the forward tube support to become the latch retention system for the end of the inner load tube.The new model case hardened .44 and the new side loaders use a machined steel end on the mag tube. Also the carbine models.
This is a definite improvement as it will eliminate the cracking of the outer load tube by removing the 'stress' that has caused the cracking - which is still a mystery to me.
I have thought about it and I am THINKING when the tube is full and the first shot is fired it somehow transfers impact through all the rounds and hammers the inner tube forward, which eventually cracks the outer tube due to the lock pin pushing against it.
I can't really see any other way for this to happen and looking at the new system I see no reason an existing rifle could not be converted. It would require a new tube support, a new (or shortened) inner tube and most likely a shorter inner tube.
0 x
Re: Magazine Tube Replacement
I don’t think the magazine is fully loaded during test fire—I may be wrong on that. What I found on the one I purchased was the outer mag tube was distorted where it meets the receiver. I’m pretty sure this would be caused by blow-by, causing the already weak area to deform.
0 x
Re: Magazine Tube Replacement
Ok here is the update after many emails and calls the UK importer has agreed that there is no damage other than the crack in the tube and Henry has agreed the free replacement. Due to the difficulties and cost of posting firearms in UK the importer will post the tube to my gunsmith who will replace the tube and return the gun to at the range where we both shoot, I will pay him for the work and we are all happy. The cost to me is smaller than the shipping costs if I were to return the gun to the importer.
4 x
Re: Magazine Tube Replacement
Mistered, I think you're on to something. When the gun fires, the recoil is a push to the rear, but the cartridges want to remain in place, so their inertia effectively "taps" forward on the tube. Not a lot different than a rifle scope moving forward in its rings on a heavy recoiling rifle. Over time, I can see how there could be some effect, especially with relatively heavy cartridges, like .44 Remington or, especially, .45-70.
0 x
Re: Magazine Tube Replacement
Probably not but I was referring to the tubes that crack much later after the owner has owned the rifle for some time.I don’t think the magazine is fully loaded during test fire—
In this case I am sure the mag tube had been loaded full many times.
0 x
Re: Magazine Tube Replacement
That is exactly what happens...it becomes a slide hammer! I had made a ring years ago that slid over the end of the tube on my H010, just to strengthen it, but it only slowed down the deformation. Eventually it became hard to turn the tube to release it, so I sent it in for the updated parts.Yornoc3 wrote: ↑Tue Jun 18, 2019 11:20 amMistered, I think you're on to something. When the gun fires, the recoil is a push to the rear, but the cartridges want to remain in place, so their inertia effectively "taps" forward on the tube. Not a lot different than a rifle scope moving forward in its rings on a heavy recoiling rifle. Over time, I can see how there could be some effect, especially with relatively heavy cartridges, like .44 Remington or, especially, .45-70.
Last edited by Shawn1974 on Wed Jun 19, 2019 7:07 pm, edited 1 time in total.
0 x
Re: Magazine Tube Replacement
So glad to hear you got a suitable outcome to your issue! Please keep us posted on how the repair goes and what you think when you get it back!Firefly wrote: ↑Tue Jun 18, 2019 10:27 amOk here is the update after many emails and calls the UK importer has agreed that there is no damage other than the crack in the tube and Henry has agreed the free replacement. Due to the difficulties and cost of posting firearms in UK the importer will post the tube to my gunsmith who will replace the tube and return the gun to at the range where we both shoot, I will pay him for the work and we are all happy. The cost to me is smaller than the shipping costs if I were to return the gun to the importer.
0 x
BB Steel .357 | SGC 22LR | LR .308 | CCH 30-30 | BB Brass .45 Colt (Carbine) | Single Shot 20 gauge | Single Shot .223 | Single Shot 357
Re: Magazine Tube Replacement
Update.
My gunsmith has replaced the tube and returned the gun to me, the cost to me was just for his time spent on the work. He also slightly adjusted the inner tube lock to eliminate movement due to recoil that puts strain on the latch cutout slot. He is also looking at the possibility that the broken tube could be repaired.
My gunsmith has replaced the tube and returned the gun to me, the cost to me was just for his time spent on the work. He also slightly adjusted the inner tube lock to eliminate movement due to recoil that puts strain on the latch cutout slot. He is also looking at the possibility that the broken tube could be repaired.
3 x