Spring has sprung. Get out and shoot your Henry

Not So Pretty Woodworking Project

User avatar
JEBar
Town Marshal / Deputy Admin
Posts: 19270
Joined: Sun Mar 20, 2016 10:58 pm
Location: central NC
United States of America

Not So Pretty Woodworking Project

Post by JEBar » Mon Dec 18, 2017 6:04 pm

our camper was built during October of '05 .... since then it has bounced down tens of thousands of miles of highways, taking us through all of the continental 48 states .... with any recreational vehicle, ongoing maintenance and repairs are a fact of life .... the more/harder they are used, the more important maintenance becomes .... today's repair effort centered on taking care of water damage to the edge of the camper's bedroom slide floor ... pictures 1 & 2 show the water damage ..... picture 3 shows the separations filled with wood glue to the point it was running out (uses a turkey hypodermic to force the glue deep into the openings) .... the last three pictures show the way I rigged up a way to press the separations back together .... in the last picture a dark section can be seen on the left .... using a different turkey hypodermic, hardener forced into the area in a hope of saturating it .... this is the first time I've used hardener and I must say I've been pleasantly surprised .... it has gone from feeling spongy to very hard .... my plan is to force more hardener into the area several times tomorrow in the hope of not missing any areas with decay ..... once this process is complete, I plan to saturate the exposed edge of the plyboard with a Thompson's Water Seal type product .... sometime during the week after Christmas we hope to spend a good bit of time and effort to ensure that the area is sealed to prevent future water penetration ... pictures will be added as this project continues
Attachments
171211 002 delaml 002.jpg
171211 002 delaml 002.jpg (33.86 KiB) Viewed 3681 times
171811 001 separated wood 001.jpg
171811 001 separated wood 001.jpg (31.38 KiB) Viewed 3681 times
171811 002 filled with glue 001.jpg
171811 002 filled with glue 001.jpg (35.76 KiB) Viewed 3681 times
171811 003 pressure applied 001.jpg
171811 003 pressure applied 001.jpg (39.18 KiB) Viewed 3681 times
171811 003 pressure applied 003.jpg
171811 003 pressure applied 003.jpg (62.79 KiB) Viewed 3681 times
171811 003 pressure applied 004.jpg
171811 003 pressure applied 004.jpg (37.92 KiB) Viewed 3681 times
0 x

User avatar
BrokenolMarine
Ranch Foreman
Posts: 5770
Joined: Sat Nov 26, 2016 8:28 am
Location: South Central Oklahoma in the mountains
United States of America

Re: Not So Pretty Woodworking Project

Post by BrokenolMarine » Tue Dec 19, 2017 7:43 am

This is outside my area of expertise, but i'll be watching... I am always interested in new projects.
Good luck.
0 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.

User avatar
JEBar
Town Marshal / Deputy Admin
Posts: 19270
Joined: Sun Mar 20, 2016 10:58 pm
Location: central NC
United States of America

Re: Not So Pretty Woodworking Project

Post by JEBar » Tue Dec 19, 2017 9:34 am

the weather forecast for the next week in our area has undergone a major downturn ... rain is now in the forecast on 3 days between now and Christmas .... the picture below is of the other end of the slideout shown in post 1 .... when we finish the repairs it should look something like the one below .... we are going to use some aluminum sealant tape as an added layer of protection from moisture penetration .... as soon as it warms up a bit I plan to go back out today an pump more hardener .... with rain due to move in late this afternoon we will pull the slide in .... our goal is to finish up on Thursday morning
Attachments
171211 001 OEM Seal 001.jpg
171211 001 OEM Seal 001.jpg (36.09 KiB) Viewed 3670 times
0 x

User avatar
GFK
Cowboy
Posts: 1918
Joined: Tue Oct 17, 2017 12:56 pm
Location: SE
United States of America

Re: Not So Pretty Woodworking Project

Post by GFK » Tue Dec 19, 2017 10:27 am

I would probably try some all weather silicone sealant as well. I put some on my used to be waterproof boots were the sole had pulled away from the boot. So far, so good. The boots are about 12 years old. Yes, I could have replaced them. But, they are in fairly good shape. And for a couple of dollars, I can have a set of boots to play in the yard or woods with. If not, I will probably spend the $100 or so to replace them.
Last edited by GFK on Tue Dec 19, 2017 4:17 pm, edited 1 time in total.
1 x
Actions speak louder than words (Matthew 7:16-20).

User avatar
JEBar
Town Marshal / Deputy Admin
Posts: 19270
Joined: Sun Mar 20, 2016 10:58 pm
Location: central NC
United States of America

Re: Not So Pretty Woodworking Project

Post by JEBar » Tue Dec 19, 2017 1:22 pm

3 coats of Behr white water proofing
Attachments
171219 001 water seal applied 001.jpg
171219 001 water seal applied 001.jpg (31.12 KiB) Viewed 3661 times
2 x

User avatar
GFK
Cowboy
Posts: 1918
Joined: Tue Oct 17, 2017 12:56 pm
Location: SE
United States of America

Re: Not So Pretty Woodworking Project

Post by GFK » Tue Dec 19, 2017 3:00 pm

Looks nice!
0 x
Actions speak louder than words (Matthew 7:16-20).

User avatar
JEBar
Town Marshal / Deputy Admin
Posts: 19270
Joined: Sun Mar 20, 2016 10:58 pm
Location: central NC
United States of America

Re: Not So Pretty Woodworking Project

Post by JEBar » Fri Dec 22, 2017 7:09 pm

project completed .... I can't thank forum member and good friend Mike (eldermike) enough for lending his knowledge and support .... step 1 was to dry out the affected area .... step 2 repair separated and deteriorated with with water repellent glue and wood hardener .... step 3 was to put in place as many layers of different water proofing as possible .... those layers include liberal applications of Behr waterproofing, layered applications of aluminizedtape, a fabricated "L" bracket made from chimney flashing, and silicone .... thankfully, no rain due until Saturday so the various adhesives, stain, and silicone will have plenty of time to setup
Attachments
171221 001  aluminized tape 002.jpg
171221 001 aluminized tape 002.jpg (39.71 KiB) Viewed 3644 times
171221 002 fitting components 002.jpg
171221 002 fitting components 002.jpg (29.45 KiB) Viewed 3644 times
171221 002 fitting components 004.jpg
171221 002 fitting components 004.jpg (33.21 KiB) Viewed 3644 times
171221 003 completed 001.jpg
171221 003 completed 001.jpg (31.56 KiB) Viewed 3644 times
2 x

User avatar
GFK
Cowboy
Posts: 1918
Joined: Tue Oct 17, 2017 12:56 pm
Location: SE
United States of America

Re: Not So Pretty Woodworking Project

Post by GFK » Sat Dec 23, 2017 10:43 am

That should do the trick!
0 x
Actions speak louder than words (Matthew 7:16-20).

User avatar
JEBar
Town Marshal / Deputy Admin
Posts: 19270
Joined: Sun Mar 20, 2016 10:58 pm
Location: central NC
United States of America

Re: Not So Pretty Woodworking Project

Post by JEBar » Sat Dec 23, 2017 3:11 pm

GFK wrote:That should do the trick!
we most certainly hope so .. :D
0 x

User avatar
Sir Henry
Administrator / Owner
Posts: 12054
Joined: Sun Mar 20, 2016 10:58 pm
Location: Price County Wisconsin
United States of America

Re: Not So Pretty Woodworking Project

Post by Sir Henry » Sat Dec 23, 2017 7:31 pm

The joys of owning an RV. Looks like you mastered the repair.
0 x
Hi, my name is Gene and I'm a Henryholic from Wisconsin.

Range Reporter: Henry Repeater

Post Reply