I'll offer again: I've got a half-dozen of these 38# mainsprings I'm willing to share. Just send me a PM and I'll ship you one to try out.Yornoc3 wrote: ↑Mon Aug 12, 2019 7:30 pmroddy,
My 45-70 is right around 3.5 to 4 lbs trigger pull weight, and I don't find the hammer cocking resistance to be excessive, either. On the other hand, the new model .308 of my son-in law and my 30-30 both could be lifted by the trigger when cocked (with a snap cap in the chamber) without ""firing. That 'd be around 7lbs, I'd say more. Replacing the mainspring, leaving the smaller one in place, cured 'em both; they're now under 4lbs in trigger pull weight.
Spring has sprung. Get out and shoot your Henry
Single Shot Hammer Spring Modification
Re: Single Shot Hammer Spring Modification
1 x
BB Steel .357 | SGC 22LR | LR .308 | CCH 30-30 | BB Brass .45 Colt (Carbine) | Single Shot 20 gauge | Single Shot .223 | Single Shot 357
Re: Single Shot Hammer Spring Modification
That, too, is good to know. Thanks! I'll be watching for any "fail to fires", particularly on the .308, when we get around to shooting those two rifles with the replaced lighter springs (Labor day weekend?). I have wondered if some ammunition may have harder primers these days, particularly loads that often are used in semi-auto actions, like .223 and .308. Or maybe just in general for liability reasons, like the use of the stronger springs in the rifles in the first place.
0 x
Re: Single Shot Hammer Spring Modification
I would take you up on that, but shipping stuff across the border can be pretty dicey...with my luck, I'd end up with a $50 'brokerage' fee, lol.ESquared wrote: ↑Mon Aug 12, 2019 9:52 pmI'll offer again: I've got a half-dozen of these 38# mainsprings I'm willing to share. Just send me a PM and I'll ship you one to try out.Yornoc3 wrote: ↑Mon Aug 12, 2019 7:30 pmroddy,
My 45-70 is right around 3.5 to 4 lbs trigger pull weight, and I don't find the hammer cocking resistance to be excessive, either. On the other hand, the new model .308 of my son-in law and my 30-30 both could be lifted by the trigger when cocked (with a snap cap in the chamber) without ""firing. That 'd be around 7lbs, I'd say more. Replacing the mainspring, leaving the smaller one in place, cured 'em both; they're now under 4lbs in trigger pull weight.
0 x
Re: Single Shot Hammer Spring Modification
We finally got around to sighting in the .308 of my S-i-L and my 30-30 over Labor Day weekend. The .308 dialed in nicely, however, it did have one fail to fire, albeit there seemed to be a solid primer strike, so go figure. The 30-30 fired just fine, but the gun show scope (older 2.5X Burris) seemed to not be adjusting properly, so I quit while I was still ahead. I'll check out the scope, if I decide I can't trust it, I'll replace it with a 2.5X Leupold ultralight (like I probably should 'a done in the first place ).
0 x
Re: Single Shot Hammer Spring Modification
Just a thought Yornoc3 I have had issues with one of the Burris scopes before and took it to them. They fixed it with no questions at all. Im lucky though no shipping for me there right near where I work everyday.
0 x
Don't worry about getting older and still doing stupid stuff. You'll do the stupid stuff as always, only much slower. Hold my beer and watch this.......
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
Re: Single Shot Hammer Spring Modification
BigAl52,
I thought that I'd send it back to Burris if I find that it's not tracking correctly, thanks for the reassurance that they'll still take care of it. It's in real nice shape, so maybe it'll free up with some exercise. I know that the springs that maintain tension on the erector tube can weaken and/or stick on older scopes, so first I'll give it a workout on a rimfire rifle and see what happens.
I thought that I'd send it back to Burris if I find that it's not tracking correctly, thanks for the reassurance that they'll still take care of it. It's in real nice shape, so maybe it'll free up with some exercise. I know that the springs that maintain tension on the erector tube can weaken and/or stick on older scopes, so first I'll give it a workout on a rimfire rifle and see what happens.
0 x
-
- Cowhand
- Posts: 255
- Joined: Wed Nov 13, 2019 8:52 pm
Re: Single Shot Hammer Spring Modification
Got the spring in my .243 single shot swapped out today - thanks to Esquared who was nice enough to send me a 38# spring. Super simple as all have noted. I didn't get out to shoot it as yet, but I will. Using a snap cap I can tell it dropped the trigger weight and the hammer cock a couple of pounds. I didn't do anything else - and I probably won't. I've only got 12-15 shots through it - so it should smooth out some with some range work. It wasn't gritty or anything - actually it's quite clean, but with more rounds through it it'll probably drop another pound with use - which will make it a perfect hunting trigger.
I've got some Hornady rounds I'll use to test the rifle with - Hornady (as I've read) tends to have harder primers. So if it passes the Hornady test, we'll be good to go.
Many thanks again, and I'll let everyone know how it goes.
I've got some Hornady rounds I'll use to test the rifle with - Hornady (as I've read) tends to have harder primers. So if it passes the Hornady test, we'll be good to go.
Many thanks again, and I'll let everyone know how it goes.
1 x
- JEBar
- Town Marshal / Deputy Admin
- Posts: 19348
- Joined: Sun Mar 20, 2016 10:58 pm
- Location: central NC
Re: Single Shot Hammer Spring Modification
zara_puppy wrote: ↑Mon Dec 09, 2019 6:34 pmI've got some Hornady rounds I'll use to test the rifle with - Hornady (as I've read) tends to have harder primers. So if it passes the Hornady test, we'll be good to go.
good to know .... I wasn't aware of that ....
0 x
Re: Single Shot Hammer Spring Modification
Yes do lt us know. I dont think Evan has put many rounds through his since he went to a 38 lb spring. I have a bag of the lighter springs which worked fine in my 357 but I never did use any of the 38lb springs.
0 x
Don't worry about getting older and still doing stupid stuff. You'll do the stupid stuff as always, only much slower. Hold my beer and watch this.......
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
-
- Tenderfoot
- Posts: 2
- Joined: Sat Feb 23, 2019 11:00 am
Re: Single Shot Hammer Spring Modification
I second the question. Does anyone want to share the Grainger part number for this spring?
0 x