Spring has sprung. Get out and shoot your Henry
Removing scratch in Brass?
Removing scratch in Brass?
I just got my gun back after warranty service and there is a small scratch in the brass receiver and a slight ding in the bluing on the barrel. One of the reasons I fix my own motorcycles and fix my own guns but ... I can just touch up the barrel with a bluing pen but .. is there a way to buff out the small surface scratch on the brass without damaging it and making it look prepared. Its not deep .. guess I could just leave it alone but if there is a light buffing compound I would go for it.
Thank you for any advice!
Thank you for any advice!
0 x
- RanchRoper
- Forum Ambassador
- Posts: 12692
- Joined: Mon Mar 21, 2016 12:14 am
- Location: Land of Shining Mountains, Alberta
Re: Removing scratch in Brass?
What you need is a good story to go with that scratch and I think a grizzly should be part of it somehow... ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)
2 x
1860 Colt SA Richards Conversion Revolver .45C
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
Re: Removing scratch in Brass?
Maybe with a better outcome than this however....
You do not have the required permissions to view the files attached to this post.
0 x
- RanchRoper
- Forum Ambassador
- Posts: 12692
- Joined: Mon Mar 21, 2016 12:14 am
- Location: Land of Shining Mountains, Alberta
Re: Removing scratch in Brass?
Yikes..maybe better buff that scratch out.
0 x
1860 Colt SA Richards Conversion Revolver .45C
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
Re: Removing scratch in Brass?
You might try brasso. It contains an extremely fine abrasive that might help. It will take a lot of rubbing however. Normally used just for tarnish removal and polishing.
1 x
Bellum Omnium Contra Omnes is rapidly becoming a reality (11/2023). Para Bellum.
Re: Removing scratch in Brass?
I like the way you think!!!RanchRoper wrote: ↑Thu Dec 12, 2019 12:49 pmWhat you need is a good story to go with that scratch and I think a grizzly should be part of it somehow...![]()
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
Unfortunately its more like a mosquito landed on it and was drunk so skidded into his landing .. Just doesnt sound as impactful as I would like!!
I may give some brasso a try. Having been in the military a thousand years ago .. me and brasso had a thing. These fingers have seen lots o brasso.
0 x
Re: Removing scratch in Brass?
FWIW I recently tried Brasso on my BBB and it was like grease on glass. Barely did a thing.
2 x
- Shakey Jake
- Drover
- Posts: 4346
- Joined: Wed Aug 16, 2017 11:10 am
- Location: Sugar Land, TX
- Contact:
Re: Removing scratch in Brass?
I work with saxophones as I repair woodwinds. Minor scratches can be taken out with tripoli followed by white diamond then red rouge. I have a floor buffer that uses some fairly large buffing wheels. I know Dremel sells sets with small buffing wheels as well as polishing compound. I don't know if Henry sprays these with lacquer or not but imagine they do. You'd have to coat the buffed area with clear lacquer to keep it from turning a different patina than the rest of the receiver. I use Behlin or Mohawk clear lacquer spray in aerosol cans for touch up masking off areas to prevent overspray.
2 x
Re: Removing scratch in Brass?
I thought i read somewhere here that there us not a coating. Still not sure. I have a block of green rouge and one of white and a dremel with buffing wheels but i am afraid that will make the "repair" to localized and actually look worse than the scratch. Someth8ng like brasso i could have used more broadly but if it doesnt work maybe flitz?
0 x
Re: Removing scratch in Brass?
I looked into it and there is NOT a coating on the BBB receivers.I thought i read somewhere here that there us not a coating.
Because the receivers are gunmetal and not brass per se they are considerably harder and probably why the Brasso was ineffective.
2 x