Spring has sprung. Get out and shoot your Henry
How to make the Ghost Ring sight.....
- fortyshooter
- Ranch Foreman
- Posts: 6343
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
How to make the Ghost Ring sight.....
Use a basic hacksaw blade because the mounting holes are about .150 diameter and the material is hard so locking screw won't dent.
I lay the Henry sight insert on top of blade material and center it up with blade hole. Use a White colored hacksaw blade so your scribe marks will show up clearly. Holding blade I carefully grind to each side line mark paying attention to keep it square and sides parallel to each other.
Make sure to keep the hole centered to the sides! Grind for a slide in fit into the Henry Sight holder...not to loose. Should measure .245-.250 in width.
Then cut to length using Dremel type cutting disc to 3/16ths of an inch below bottom of hole in blade. Do not grind the top edge of blade as it already has a nice finished radiused edge. Total new insert length should be 9/16ths of an inch.
You can remove the blade paint with Acetone for a nice blued look!
I lay the Henry sight insert on top of blade material and center it up with blade hole. Use a White colored hacksaw blade so your scribe marks will show up clearly. Holding blade I carefully grind to each side line mark paying attention to keep it square and sides parallel to each other.
Make sure to keep the hole centered to the sides! Grind for a slide in fit into the Henry Sight holder...not to loose. Should measure .245-.250 in width.
Then cut to length using Dremel type cutting disc to 3/16ths of an inch below bottom of hole in blade. Do not grind the top edge of blade as it already has a nice finished radiused edge. Total new insert length should be 9/16ths of an inch.
You can remove the blade paint with Acetone for a nice blued look!
You do not have the required permissions to view the files attached to this post.
Last edited by fortyshooter on Sun Apr 05, 2020 12:39 pm, edited 1 time in total.
14 x
- Vaquero
- Ranch Boss
- Posts: 10403
- Joined: Mon Mar 21, 2016 12:56 am
- Location: Somewhere between Memphis & Nashville
Re: How to make the Ghost Ring sight.....
Thanks forty, I'm going to try one.
RP
RP
0 x
Monte Walsh "You have No idea how little I care".
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
- CT_Shooter
- Administrator emeritus
- Posts: 5163
- Joined: Mon Mar 21, 2016 8:42 am
- Location: Connecticut
Re: How to make the Ghost Ring sight.....
Forty, this is an ingenious improvement to the standard semi-buckhorn sights that come with most Henrys. Thanks for sharing it with us. I'm sure there will be many who will give it a try.
0 x
H006M Big Boy Brass .357 - H001 Classic .22LR - Uberti / Taylors & Co. SmokeWagon .357 5.5" - Uberti / Taylors & Co. RanchHand .22LR 5.5"
- fortyshooter
- Ranch Foreman
- Posts: 6343
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
Re: How to make the Ghost Ring sight.....
My pleasure! I added another picture showing finished sight insert! If anyone has a question I be happy to help!
2 x
Re: How to make the Ghost Ring sight.....
Excellent idea!Use a basic hacksaw blade because the mounting holes are about .150 diameter
Hacksaw blade has been has made me a few replacement sight blades over the years as well!
0 x
Re: How to make the Ghost Ring sight.....
The tool and die maker talent their shows. Ive seen the tools that Forty has to. So a guy with no grinder and other tools will just half to drool.
0 x
Don't worry about getting older and still doing stupid stuff. You'll do the stupid stuff as always, only much slower. Hold my beer and watch this.......
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
Re: How to make the Ghost Ring sight.....
Good job, forty. Glad to see another T&D maker at work. May give it a go when I get caught up on my pressing projects, ( chainsaw on BIG limb on the ground, replacing wood on outside of my shed/shop, I didn't get finished last year before bad weather set in ).
Too many irons in my little fire, LOL.
Too many irons in my little fire, LOL.
1 x
I rarely ever buy a rifle, but when I do, it's a Henry.
"Every day above ground, is a good day" ( Al Capone )
"Every day above ground, is a good day" ( Al Capone )
- Vaquero
- Ranch Boss
- Posts: 10403
- Joined: Mon Mar 21, 2016 12:56 am
- Location: Somewhere between Memphis & Nashville
Re: How to make the Ghost Ring sight.....
That should work well on my Marlin Cowboy also.
The rear sights are very similar.
RP
The rear sights are very similar.
RP
0 x
Monte Walsh "You have No idea how little I care".
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
- fortyshooter
- Ranch Foreman
- Posts: 6343
- Joined: Sat Dec 09, 2017 10:37 am
- Location: Va.
Re: How to make the Ghost Ring sight.....
If you make one post up a review if you get a chance. Just want to see how it works out for other folks!
0 x
- Vaquero
- Ranch Boss
- Posts: 10403
- Joined: Mon Mar 21, 2016 12:56 am
- Location: Somewhere between Memphis & Nashville
Re: How to make the Ghost Ring sight.....
Yes sir, you should know I would, as verbal I get.fortyshooter wrote: ↑Tue Apr 07, 2020 9:42 amIf you make one post up a review if you get a chance. Just want to see how it works out for other folks!
Ask Al.
RP
1 x
Monte Walsh "You have No idea how little I care".
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012
Ain't No Apologies for My Temperament
Si vis pacem, para bellum
H001, H006, H012