Spring has sprung. Get out and shoot your Henry
A New Build (Along)
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
The scalpel case? Not going to go into a long narrative and how to, but here is the case. I hand stitched this one, using the stitching pony, I was pretty happy with the results. The bulge at the bottom is a small piece of leather to act as a stop so the blade doesn't cut thru the stitching. After all, this thing is as sharp as a surgical scalpel.
Stitching pony holds the piece while you sew, I made mine from a few different designs I saw on line, combining the best features I liked from each. One thing that "I" added was the magnets to hold the needles on each side. I was going to put them flush, then I realized that installed proud, they would make the needles easier to retrieve.
The pony:
Back side:
The finished piece. I like how the stitching turned out. I finished the sheath in Yellow and antiqued it.
Stitching pony holds the piece while you sew, I made mine from a few different designs I saw on line, combining the best features I liked from each. One thing that "I" added was the magnets to hold the needles on each side. I was going to put them flush, then I realized that installed proud, they would make the needles easier to retrieve.
The pony:
Back side:
The finished piece. I like how the stitching turned out. I finished the sheath in Yellow and antiqued it.
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
The problem I had been trying to solve was that the dado in the mahogany trim didn't lend itself to securely attaching the hinges for the lid. I could go with strap hinges, sometimes called "Trunk" hinges, but I didn't like the look of those. I decided to use reinforcement blocks in the hinge location and notch the velvet liner and insure it was glued securely in that location. Not like there would be a lot of stress anyway.
This would allow a bite for the four screws and should support the hinges, especially if I used contact cement on the hinges and the mahogany.
This would allow a bite for the four screws and should support the hinges, especially if I used contact cement on the hinges and the mahogany.
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
My other concern here was the filling of the crack on the corner and some deep holes / faults in the top. I had used wood putty that is claimed to accept stain. Every time I looked at that putty it bothered me. So, I used the scalpel's sharp tip to pop the filler out of the crack and the holes I had filled and pulled one of the bottles of sawdust I save for just this purpose. They are labeled by species. I chose black walnut. I mixed it into a paste using ebony stain. Again, using the scalpel for it's fine tip, I filled the crack.
Next I filled the holes and voids using the same mixture.
I pulled my Satellite City special glue made for filling gaps and cracks from the shelf, and got ready to bind and seal the repairs. All three tubes were hard as rocks. They had been on the shelf for years since the last use... Trip to home depot, not carried. Ordered on Amazon. A week...
No matter, before you use the product, you are wise to stain the surrounding area as they penetrate and THAT area won't stain. So, while WE wait together for the arrival of the special glue, I prepped and stained the top and the box. Now check out the crack....
As I had been promising, I used the Golden Oak Watco Oil, and that grain has POPPED.
That Osage Orange Box is looking pretty good as well. I did NOT stain the top edge, because glue won't hold well on watco oiled surfaces.
Next I filled the holes and voids using the same mixture.
I pulled my Satellite City special glue made for filling gaps and cracks from the shelf, and got ready to bind and seal the repairs. All three tubes were hard as rocks. They had been on the shelf for years since the last use... Trip to home depot, not carried. Ordered on Amazon. A week...
No matter, before you use the product, you are wise to stain the surrounding area as they penetrate and THAT area won't stain. So, while WE wait together for the arrival of the special glue, I prepped and stained the top and the box. Now check out the crack....
As I had been promising, I used the Golden Oak Watco Oil, and that grain has POPPED.
That Osage Orange Box is looking pretty good as well. I did NOT stain the top edge, because glue won't hold well on watco oiled surfaces.
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
I'll use the Medium Walnut on the Mahogany trim once the glue sets and the excess is cleaned up. The big pucker factor will be setting the hinges as I will have to cut the slots for them to rest in. Slip and it will be a big OOPS...
0 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
A little work in the shop. Some minor fitting today, and checking the finish. I did some more filling of the cracks and gaps while still waiting for the special T glue to come in next week. Specifically the knots in the box sides. Somewhat stalled until then. Mixed feelings on the color difference in the osage orange and the Maple, but ... Not sure if I want to attempt to darken the osage to more closely match the top.
We are in the final stages. I am going to work on a logo insert. Yup. For the inside of the top.
We are in the final stages. I am going to work on a logo insert. Yup. For the inside of the top.
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
I've got the logo insert done, and I took pics of the modification to the Mahogany Rail to allow for installation of the hinges and the foam tray that will eventually be covered in Velvet. So, first, here is a look at the foam tray that the knife will lay in when it's in the box.
Next up, the 1-1/8" block fillers so the hinge screws will have something to bite into other than blank space.
Lastly, here is the 5/8" diameter leather disk that will be inlaid into the underside of the box lid, in the lower right corner. It has my Maker's Mark stamped in the center. I dyed it red to accent the burgundy liner of the box. Hopefully it will all look good when it's all put together. Waiting on the special T glue.
The disk still needs the edges burnished and some finish on it, but you get the idea.
Next up, the 1-1/8" block fillers so the hinge screws will have something to bite into other than blank space.
Lastly, here is the 5/8" diameter leather disk that will be inlaid into the underside of the box lid, in the lower right corner. It has my Maker's Mark stamped in the center. I dyed it red to accent the burgundy liner of the box. Hopefully it will all look good when it's all put together. Waiting on the special T glue.
The disk still needs the edges burnished and some finish on it, but you get the idea.
You do not have the required permissions to view the files attached to this post.
2 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
Today, if I have some shop time, I may try to stain a scrap of osage to better match the color of the maple... perhaps a second pass with a 2/1 or 3/1 mixture of golden oak and medium walnut. That's what scraps are saved for... testing. LOL.
0 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
I used a scrap of wood to test the fit of the round leather logo. I didn't like the fit or the look of the logo against the grain. Too late in the game to screw up the box now by making THAT mistake. I had been thinking of filling that void UNDER the box where the dado leaves a gap where the bottom fits. I had cut a piece of leather to fit, and then a foam spacer, all I had to do was tool and stain the leather and put my maker's mark on THAT...
This piece will be under the box. You can see my maker's mark in the lower right corner.
The special glue is still due on Wednesday so we are nearly there.
This piece will be under the box. You can see my maker's mark in the lower right corner.
The special glue is still due on Wednesday so we are nearly there.
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
The Special Glue came a day early, so I got to spend Tuesday in the shop, in several sessions, working on the box. I began by applying a medium thickness covering on all the cracks and voids on the top and the sides of the box. Then I went inside and watched a couple episodes of "Hill Street Blues." I'm working my way thru the box set. This special super glue needs about an hour to properly set, then you can sand it smooth and it's as clear as glass. (They have an accelerator spray, but I found that it sometimes discolors the glue, giving it a haze rather than leaving it clear.)
After sanding the first treatment, there were areas that needed a second treatment, so I reapplied the glue and left the panels to dry again. Time for lunch, and more Hill Street. The second treatment was enough for the top of the box and I resanded the box top back up thru 1,000 grit and then marked it for the hinges. I CAREFULLY cut the mortises for the hinges. THIS was a high pucker factor operation that took nearly an hour. With each cut I was afraid I would slip and ruin the top.
Meanwhile, the third and fourth layers were applied to the deep void on the side of the front of the box. Between each application, I would sand away the buildup with 400 grit sandpaper.
After sanding the first treatment, there were areas that needed a second treatment, so I reapplied the glue and left the panels to dry again. Time for lunch, and more Hill Street. The second treatment was enough for the top of the box and I resanded the box top back up thru 1,000 grit and then marked it for the hinges. I CAREFULLY cut the mortises for the hinges. THIS was a high pucker factor operation that took nearly an hour. With each cut I was afraid I would slip and ruin the top.
Meanwhile, the third and fourth layers were applied to the deep void on the side of the front of the box. Between each application, I would sand away the buildup with 400 grit sandpaper.
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.
- BrokenolMarine
- Ranch Foreman
- Posts: 5815
- Joined: Sat Nov 26, 2016 8:28 am
- Location: South Central Oklahoma in the mountains
Re: A New Build (Along)
Once I had finally finished the stabilizing of the components, I wiped them down with mineral oil to remove the sawdust and test fitted all the parts together to see how they would look. You can see that the gaps and voids that once were visible in the top are now as smooth as glass.
That deep corner crack that was 1/8" wide in some spots, and 1/8" deep, is now flush and smooth. That fill technique worked, it's black and matte and looks pretty good in my opinion. Looks natural. Rather than a flaw, it's become simply part of the spalting character of the wood.
A view from the front let me know that I would have some "Minor" shaping to do on the mahogany trim once the box is assembled, rolling the top edge to blend the pieces. Other than that, it's a good fit.
A look at the back of the box shows that the hinges won't look too bad. (No screws in place, it's a mock up.) I think they will accent the piece. I might have gone with black hinges if I had any the right size. But, the knife is trimmed in Brass so the inside view will be complimented by the brass hinges.
That deep corner crack that was 1/8" wide in some spots, and 1/8" deep, is now flush and smooth. That fill technique worked, it's black and matte and looks pretty good in my opinion. Looks natural. Rather than a flaw, it's become simply part of the spalting character of the wood.
A view from the front let me know that I would have some "Minor" shaping to do on the mahogany trim once the box is assembled, rolling the top edge to blend the pieces. Other than that, it's a good fit.
A look at the back of the box shows that the hinges won't look too bad. (No screws in place, it's a mock up.) I think they will accent the piece. I might have gone with black hinges if I had any the right size. But, the knife is trimmed in Brass so the inside view will be complimented by the brass hinges.
You do not have the required permissions to view the files attached to this post.
1 x
You can tell a lot about the character of a man...
by the way he treats those who can do nothing for him.
by the way he treats those who can do nothing for him.