Spring has sprung. Get out and shoot your Henry
Dillon reloader
Re: Dillon reloader
I have a Dillon 650 with a case feeder.
You can't go wrong with Dillon. If you break something even if it's your fault they will send you a new one.
No BS lifetime warranty.
You can't go wrong with Dillon. If you break something even if it's your fault they will send you a new one.
No BS lifetime warranty.
0 x
Henry H004 Golden Boy
Henry H006 Big Boy 44
Henry H010B 45-70
NRA Benefactor Member
Henry H006 Big Boy 44
Henry H010B 45-70
NRA Benefactor Member
- RanchRoper
- Forum Ambassador
- Posts: 12692
- Joined: Mon Mar 21, 2016 12:14 am
- Location: Land of Shining Mountains, Alberta
Re: Dillon reloader
This Lee classic turret press kit looks ok too; I like it that I don't have to change dies all the time.
What is trimming brass all about? Would I be doing that with 1 time fired 45 Colt? How many times do you reload the same brass?
What is trimming brass all about? Would I be doing that with 1 time fired 45 Colt? How many times do you reload the same brass?
- Attachments
-
- th.jpg (8.77 KiB) Viewed 2018 times
0 x
1860 Colt SA Richards Conversion Revolver .45C
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
- CT_Shooter
- Administrator emeritus
- Posts: 5156
- Joined: Mon Mar 21, 2016 8:42 am
- Location: Connecticut
Re: Dillon reloader
If you have a large bag of mixed headstamp cases, they could have tiny variations in their lengths. That can be issue during the crimping process. I've always been careful to keep my brass in the same lots of fifty that came from the factory and I don't trim them; I just set the crimping die for each lot before I reload them. I do have a few boxes of mixed brass that I was given. I immediately trimmed all of them to insure uniformity, thereafter, I use and save them in the same lot of fifty and don't trim them again.RanchRoper wrote:What is trimming brass all about? Would I be doing that with 1 time fired 45 Colt? How many times do you reload the same brass?
I'm rotating an inventory of about 1200 cases and have some that have been reloaded eight times. I check each one during the priming process and again after crimping for any signs of wear. (I prime my cases right after cleaning them, then box them to be reloaded later.) I'm also careful to use just enough of a flare to hold the bullet and keep it from falling off so that the brass doesn't get stretched any more than is necessary.
TxGunRunner has reloaded some of his brass with cowboy loads hundreds of times.
0 x
H006M Big Boy Brass .357 - H001 Classic .22LR - Uberti / Taylors & Co. SmokeWagon .357 5.5" - Uberti / Taylors & Co. RanchHand .22LR 5.5"
- JEBar
- Town Marshal / Deputy Admin
- Posts: 19347
- Joined: Sun Mar 20, 2016 10:58 pm
- Location: central NC
Re: Dillon reloader
that is most certainly a major plus with a turret press ... with you only loading 45 Colt, once the press is setup , you'd be all but ready to go at any secondRanchRoper wrote:This Lee classic turret press kit looks ok too; I like it that I don't have to change dies all the time.
over time, casings stretch and need to be trimmed back to standard length .... its one of those things I used to obsess over .... so long as the lip of the casing crimps in the crimping groove, I don's worry about itRanchRoper wrote:What is trimming brass all about? Would I be doing that with 1 time fired 45 Colt?
that varies and is influenced by several factors ..... among them are strength of charge, quality of the casing, material the casing is made of, type of crimping, amount of expansion allowed by the chamber from which it is fired .... I have some that have been around for decades .... having saved the casings you've fired, you should be good to go for a whileRanchRoper wrote:How many times do you reload the same brass?
0 x
- RanchRoper
- Forum Ambassador
- Posts: 12692
- Joined: Mon Mar 21, 2016 12:14 am
- Location: Land of Shining Mountains, Alberta
Re: Dillon reloader
I have to do some thinking on it. Realistically I shoot maybe 1200 rounds a year based on 7 months of ideal weather. 1500 tops. At about .80 cents a round need to think about it. Equipt, lead, powder, etc. Plus time.
0 x
1860 Colt SA Richards Conversion Revolver .45C
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
Re: Dillon reloader
Lets see here scoop snow off the roof or reload 45 colt for fun. There does that help any
2 x
Don't worry about getting older and still doing stupid stuff. You'll do the stupid stuff as always, only much slower. Hold my beer and watch this.......
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
H001T .22LR
H001T .22LR MONUMENT VALLEY
H003T PUMP .22LR
BBS .41 MAG
SS .357
SIDE GATE 38-55
- RanchRoper
- Forum Ambassador
- Posts: 12692
- Joined: Mon Mar 21, 2016 12:14 am
- Location: Land of Shining Mountains, Alberta
Re: Dillon reloader
Haha...I hear ya. Thanks for all the input guys.
0 x
1860 Colt SA Richards Conversion Revolver .45C
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
- JEBar
- Town Marshal / Deputy Admin
- Posts: 19347
- Joined: Sun Mar 20, 2016 10:58 pm
- Location: central NC
Re: Dillon reloader
RanchRoper wrote:I have to do some thinking on it. Realistically I shoot maybe 1200 rounds a year based on 7 months of ideal weather. 1500 tops. At about .80 cents a round need to think about it. Equipt, lead, powder, etc. Plus time.
I look at the equipment being a 1 time expense .... the same is true for the rifle .... on the other hand, consumables are reoccurring expenses .... looking at it from that viewpoint, reloading provides considerably more bang for the buck (sorry, couldn't resist) .... the longer a person intends to shoot, the stronger the case for loading your own
1 x
Re: Dillon reloader
I've been hand loading ammo for over 45 years now. Started out on a Lee Loader hand tool set for 16 gauge. Slow process but made wonderful ammo. Got into pistol and rifle out of high school and purchased a Lyman Spartan single stage press for 20 bucks used. Still use that press today. Several years ago I got my first Dillon Square Deal. Best money I ever spent. To answer your question I would say YES to rolling your own ammo. Progressive outfits make a lot of rounds fast but beware! If you are careless or don't pay attention to detail you can make a lot of junk quickly also!
3 x
I can remember saying I'd never own a GLOCK,never own an AR15 and never get married. I found out that never is a long,long time!
- RanchRoper
- Forum Ambassador
- Posts: 12692
- Joined: Mon Mar 21, 2016 12:14 am
- Location: Land of Shining Mountains, Alberta
Re: Dillon reloader
I also saw a couple of youtube videos where guys seemed to be quite focused on "static electricity" while reloading. Ok I get it, it's gunpowder, but is this something that's an issue you think about when you reload? Just curious. If I blow myself up my wife will kill me.
1 x
1860 Colt SA Richards Conversion Revolver .45C
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully
1860 Henry .45C
1885 High Wall .45C
1820-1840 Frontier Percussion .50
1790-1820 Frontier Flintlock .50
Ohkínohkomit - Shoot skillfully