Spring has sprung. Get out and shoot your Henry
Case trimming
Re: Case trimming
If ya don't already have one I highly recommend a Lee factory crimp die - especially with 30-30. If after checking length and if some are a bit short load them anyway. Unlike roll crimping the factory crimp die does not require exacting length to crimp.
0 x
- clovishound
- Drover
- Posts: 2084
- Joined: Wed Apr 13, 2016 4:18 pm
- Location: Summerville SC
Re: Case trimming
+1 on the Lee FCD for rifle calibers. They are the way to go in my book. Just keep in mind the pistol caliber FCDs are a different animal. IOW they are not collet style crimp dies, they are either roll or taper crimp with a sizing ring. The rifle FCDs are collet style. You get consistent crimps without regard to case length. As long as it is in specs, you are good to go.
0 x
There is, I think, humor here which does not translate well from English to sanity. - Sanya
Re: Case trimming
On straight walled cases I don't trim them very often. On tapered cases I check and trim if needed. I trim and chamfer the case clean them and neck size them if I am going to shoot them is the same rifle. if I am going to shot in another rifle I will full resize them. Each round I load is given a crimp both pistol and rifle. I use all Lee reloading equipment. I reload 380, 9mm, 38spl, 357mag, 40 S&W, 44 spl, 44mag, 45 acp, 45colt, 7.62x 51, 5.53, M1 carbine, 7.62x39.
0 x
Life is short, Live life, shoot more.
S&W 686 4 Inch, S&W 686 3 inch, 686 S&W 2.5 Inch, S&W m 29-2 4 inch, Springfield Armory XD 9, 1911, Loaded, Mil-Spec, Compact 1911,Ranger Officer 9 mm, Colt 1911 Comp,
S&W 686 4 Inch, S&W 686 3 inch, 686 S&W 2.5 Inch, S&W m 29-2 4 inch, Springfield Armory XD 9, 1911, Loaded, Mil-Spec, Compact 1911,Ranger Officer 9 mm, Colt 1911 Comp,
Re: Case trimming
Sorry to pluck a quote out of a thread from 9 months ago, but I'm still doing my due diligence research on reloading, getting very specific to my situation, which is that I would start by reloading my Henry's only - 357 Mag, 30-30 and 308.Mistered wrote:After every shot with bottleneck cases - never with straight wall pistol. I use the basic Lee case length gauge & trimmer so I am limited to trimming to the prescribed length but it has never been a problem.I just wondered how accurately everyone trims their brass and how often.
None of these beginner "Kits" come with trimmers, and BigAl has turned me onto The World's Finest Trimmer as the likely solution for my 30-30 and 308 trimming, but finding much online about trimming 357 Magnum for rifles is proving difficult. This thread, in fact, has more current info than anything I've found (at least from actual users).
I'll be starting out with a batch of NEW, unfired Hornady 357 brass (200 rounds), and about 200 rounds of once-fired 357 Fiocchi brass (that's been fired in my BBS).
The questions seem to be:
1. Do I need to double check all that new brass for length and trim anything over X case length?
2. Will I need to check the Fiocchi once-fired and trim it, too, if it exceeds some case length?
3. If Yes is the answer to 1 or 2 above, is there a decent straight-wall trimmer to look into, since it will be just for this caliber for now (I may look at reloading 45 ACP down the road, but no time soon)?
Seems like even many wheelgun shooters who can run into problems with 357s that are too long interfering with cylinder rotation never give trimming a second thought and never do it. Is the Henry chamber even more forgiving and I don't need to either?
Thanks in advance, as always!
0 x
BB Steel .357 | SGC 22LR | LR .308 | CCH 30-30 | BB Brass .45 Colt (Carbine) | Single Shot 20 gauge | Single Shot .223 | Single Shot 357
Re: Case trimming
Probably because few reloaders ever trim pistol brass. It does not ‘Grow’ like bottleneck rifle brass and if you use a collet style crimp die (factory crimp die) then length with pistol brass is not an issue.but finding much online about trimming 357 Magnum for rifles is proving difficult.
Last edited by Mistered on Fri Oct 26, 2018 3:42 pm, edited 2 times in total.
0 x
Re: Case trimming
Probably because few reloaders ever trim pistol brass. It does not ‘Grow’ like bottleneck rifle brass and if you use a collet style crimp die (factory crimp die) then length with pistol brass is not an issue.but finding much online about trimming 357 Magnum for rifles is proving difficult.
The chamber length of most any pistol round rifle will be long enough to virtually never have a problem with untrimmed brass.
1 x
Re: Case trimming
Thanks, Ed. I'll scratch this off my list.Mistered wrote:Probably because few reloaders ever trim pistol brass. It does not ‘Grow’ like bottleneck rifle brass and if you use a collet style crimp die (factory crimp die) then length with pistol brass is not an issue.but finding much online about trimming 357 Magnum for rifles is proving difficult.
The chamber length of most any pistol round rifle will be long enough to virtually never have a problem with untrimmed brass.
1 x
BB Steel .357 | SGC 22LR | LR .308 | CCH 30-30 | BB Brass .45 Colt (Carbine) | Single Shot 20 gauge | Single Shot .223 | Single Shot 357
Re: Case trimming
Pistol brass like .45 A.C.P). or 9 mm that headspaces on the case mouth, need to be kept trimmed to specs.
0 x
Re: Case trimming
Yep, I figured. Not crossing that bridge yet. For me, that'll be Reloading 2.0!Travlin wrote:Pistol brass like .45 A.C.P). or 9 mm that headspaces on the case mouth, need to be kept trimmed to specs.
1 x
BB Steel .357 | SGC 22LR | LR .308 | CCH 30-30 | BB Brass .45 Colt (Carbine) | Single Shot 20 gauge | Single Shot .223 | Single Shot 357
Re: Case trimming
Do you actually trim all your.45 ACP and 9 MM you reload?Pistol brass like .45 A.C.P). or 9 mm that headspaces on the case mouth, need to be kept trimmed to specs.
0 x