Spring has sprung. Get out and shoot your Henry
Rifle Case Trim
Rifle Case Trim
Hopefully, I can get your thoughts on the topic of rifle case trimming.
Reloading manuals don’t give any tolerances with their case trim dimensions. And we know you don’t cut the whole bunch on exactly the same dimension.
When it comes to trim length on rifle cases, I usually use +/- .003” as acceptable. I’m not sure how much case-to-bullet tension is affected in that range. What tolerances do you use? And do you see much of an effect with variations larger than +/- .003”?
Also, how low is too low on trim length? I’m aware of the headspace issues for an oversize case, but how low below trim length do you find acceptable, safe and useful?
Thanks.
Reloading manuals don’t give any tolerances with their case trim dimensions. And we know you don’t cut the whole bunch on exactly the same dimension.
When it comes to trim length on rifle cases, I usually use +/- .003” as acceptable. I’m not sure how much case-to-bullet tension is affected in that range. What tolerances do you use? And do you see much of an effect with variations larger than +/- .003”?
Also, how low is too low on trim length? I’m aware of the headspace issues for an oversize case, but how low below trim length do you find acceptable, safe and useful?
Thanks.
0 x
-
- Cowhand
- Posts: 270
- Joined: Sun Apr 02, 2017 11:10 pm
Re: Rifle Case Trim
I trim my cases to the built in trimmer stop length. Chamfer and load. Neck tension holds all bullet well. Never ever had a problem.
0 x
Re: Rifle Case Trim
Most of my manuals show a maximum case length and a trim to length. The .30/06 for example is 2.494" max with a trim to length of 2.484". Back in my precision shooting days I bought a L.E. Wilson case trimmer. It requires a different case holder for each "family of cartridges" such as .243 Win, 260 Rem, 7/08 Rem and .308 Win can all use the same case holder. It will trim cases consistently within .001". I doubt if that sort of precise trimming is necessary in a factory production rifle and doubt if .003" variation would be noticeable on paper.
Case trimming is my least favorite part of handloading but when cases reach maximum I grit my teeth and start cranking. Case trimmers have progressed a lot since this 45 year old Wilson but someone else will have to chime in on the latest developements.
Case trimming is my least favorite part of handloading but when cases reach maximum I grit my teeth and start cranking. Case trimmers have progressed a lot since this 45 year old Wilson but someone else will have to chime in on the latest developements.
2 x
Re: Rifle Case Trim
You're sure getting the most out of that Wilson!
I'm using a Lyman Universal with a drill to drive the cutter. I also have a Lyman Express which works pretty well.
Ever have cases that you found to be shorter than you would use? If so, how much shorter than Trim length were they?
I'm using a Lyman Universal with a drill to drive the cutter. I also have a Lyman Express which works pretty well.
Ever have cases that you found to be shorter than you would use? If so, how much shorter than Trim length were they?
0 x
Re: Rifle Case Trim
Unless custom crimping each round, I would think that case length tolerance would affect aggressiveness of the crimp on the bullet.
2 x
UPDATES: OR passes 114, "one of strictest gun control measures in U.S." https://henryrifleforums.com/viewtopic. ... 34#p213234
Re: Rifle Case Trim
I haven't encountered that much with rifle brass. I did have a fairly recent experience with a bag of Winchester .44 magnum brass that had several cases that were way short. As Mags pointed out, when using a heavy roll crimp that would make a big difference, especially so if you were using a slow burner like H110. A consistent crimp would be critical for accuracy. In a rifle where you are just using case neck tension and there is no crimp cannelure my guess is a few thousandths of case length would not make as much difference.NHshtr wrote: ↑Fri Dec 01, 2023 11:12 amYou're sure getting the most out of that Wilson!
I'm using a Lyman Universal with a drill to drive the cutter. I also have a Lyman Express which works pretty well.
Ever have cases that you found to be shorter than you would use? If so, how much shorter than Trim length were they?
For the last decade or so I've become a fan of Starline brass. Starline has convinced me they are more consistent. I had a batch of .44 Spl brass from Winchester a few years ago where the case mouths were cut off uneven by over .010". So when a roll crimp was applied you'd get a heavy crimp on one side and barely any crimp at all on the other. To their credit they did send me a couple bags of new brass that were just fine.
0 x
Re: Rifle Case Trim
I had a couple of experiences like that with commercial rounds with "short" cases. One was Hornady 44 mag loaded with 240 XTPs. The cases, unfired, were 1.265". So, .010" shorter than "trim length" and the bullet was seated at 1.590" about .010" shorter than most manuals. So the crimp looked good and they shot well. But when I want to use those cases again, I need to watch the OAL to assure a good crimp.
The other issue was some Winchester ammo in .308 Win. that I bought to compare with my load. Those cases, unfired, were 1.990 to 2.000" or .005" to .015" shorter than Trim spec. The bullets had no cannelure, so not crimped. They didn't shoot so well from my rifle. Not as good as my load. I still have those cases, but they're socked away until I figure out whether it's worth dealing with them.
Certainly don't want to mix those in with cases at 2.005" trim. I think there'd be a worsening of groups.
The other issue was some Winchester ammo in .308 Win. that I bought to compare with my load. Those cases, unfired, were 1.990 to 2.000" or .005" to .015" shorter than Trim spec. The bullets had no cannelure, so not crimped. They didn't shoot so well from my rifle. Not as good as my load. I still have those cases, but they're socked away until I figure out whether it's worth dealing with them.
Certainly don't want to mix those in with cases at 2.005" trim. I think there'd be a worsening of groups.
0 x
-
- Cowhand
- Posts: 152
- Joined: Mon Jun 26, 2017 11:34 am
- Location: Central Massachusetts
Re: Rifle Case Trim
Although I ream the primer pocket, trim, and chamfour each case I reload, I am particularly careful in trimming cases for my M1 Garand .30-06, and .30-40 Krag. My experience is that with semi-auto, lever action, or Krag rifles, case trim lengths should not be longer than +.002" over the manual's stated C/L. Too long of a C/L can affect those rifles' ability to properly cycle a round into the chamber.
1 x
Re: Rifle Case Trim
I hear ya. That could also cause crushing the case around the bullet if it does ram in. How much case trim length tolerance do you tolerate? Is it only Case trim length plus.002"? Nothing below that?Pitchman1968 wrote: ↑Sun Dec 03, 2023 4:39 pmAlthough I ream the primer pocket, trim, and chamfour each case I reload, I am particularly careful in trimming cases for my M1 Garand .30-06, and .30-40 Krag. My experience is that with semi-auto, lever action, or Krag rifles, case trim lengths should not be longer than +.002" over the manual's stated C/L. Too long of a C/L can affect those rifles' ability to properly cycle a round into the chamber.
0 x
-
- Cowhand
- Posts: 152
- Joined: Mon Jun 26, 2017 11:34 am
- Location: Central Massachusetts
Re: Rifle Case Trim
NHshtr,
I can't remember having any short cases with new brass. With each piece of new brass, I lube, f/l size, trim, and chamfour the case prior to measuring it. Said another way, i am not concerned about factory new rifle brass being too short.
I can't remember having any short cases with new brass. With each piece of new brass, I lube, f/l size, trim, and chamfour the case prior to measuring it. Said another way, i am not concerned about factory new rifle brass being too short.
1 x