This sucks

[fortyshooter]

Great to hear everything seems to be going well BM !

[BrokenolMarine]

Headed for my two week follow up with the surgeon this morning. I guess this post could be called a teaser. I have been working the fingers, for range of motion as pain allows. I have been working the wrist for range of motion and flexibility, as pain allows. (Somewhat limited, this early, but working...) Hit the wrong angle in rotational work and...

I have not been...

Working on strength. (Docs orders)
Squeezing tennis balls. (Docs orders)
Sleeping more than two hours at a time (ah... As pain allows?)

I take catnaps, even when I don't plan too.

I will follow up post doc visit when I hope to know more.
My berm and knife projects are calling.

[markiver54]

Hope you get a positive report!

[cooperhawk]

Sleeping more than two hours at a time (ah... As pain allows?)

Carol had the same surgery and she went to a Walgreen's and purchased a compression glove and wore it at night.
She said it helped with the swelling and gave her some relief.

https://www.walgreens.com/q/arthritis+gloves

[BrokenolMarine]

Sleeping more than two hours at a time (ah... As pain allows?)

Carol had the same surgery and she went to a Walgreen's and purchased a compression glove and wore it at night.
She said it helped with the swelling and gave her some relief.

https://www.walgreens.com/q/arthritis+gloves

They removed the stitches today, and gave me a nice brace to protect the hand and apply pressure.
I can now do the hydro therapy in the tub without the vinyl sleeve.
Thanks for the suggestion... I might try it as well.
The doc was impressed with my range of motion at two weeks, said I was way ahead of the curve, wont send me to
PT at this point. "Keep doing what you are doing."

[MuddyWaters62]

Sounds Great, BOM. Wishing you continued success in your healing. Need for you to get back to old self?

Muddy Waters 67

[BrokenolMarine]

I'm trying folks. It's frustrating...
I have the projects calling my name, and I'm scratching the dog's ears and doing crosswords. Thanks to Miss T and the support of friends, I am keeping a pretty positive outlook.

[BrokenolMarine]

UPDATE...

A couple days after the checkup, Mother Nature decided to remind those of us in this area that she can play in the major leagues and it's not nice to piss off Mom.


There were Tornado Warnings, and Tornados south of us, including down where my daughter lives around the OK / TX border.

There were flood warnings, and real flooding... Right outside our door.
Yup, they told us they hadn't seen the water this high since the 90s.
We had some flooding last summer, and put the french drain around the woodshop to combat it. This was way beyond that. Our creek became a small river, then a lake, then went up and over the culvert, flooding the roadway, briefly.

Here is what is should look like.

05 down the front fence line.jpg (220.17 KiB) Viewed 649 times

Here is what is looked like about an hour before it went up over the road. The weight of the debris and water nearly took out about 40 yards of Miss Ts pasture fence, it was leaning out toward the road at a 45 degree angle when the water finally receded. She cleared the debris and pulled er back upright to keep the livestock in, but real repairs will begin when the materials come in.

creek comp.jpg (230.8 KiB) Viewed 649 times

When the rain finally stopped and I went out to check on my woodshop. You might remember it flooded last summer, then we put in that french drain. No more problems. There was water FLOWING out the rollup door. Didn't bode well for what I would find when I checked the shop.
My woodshop had water three inches deep in the lower corner, and three quarters of the floor was under water.

shop 2 comp.jpg (199.25 KiB) Viewed 649 times

I put on my brace, set up the shop vac. I and was careful, and sucked more than a dozen cannisters of water out of the woodshop. I'd estimate about 200 gallons of water from the woodshop, another 100 from the boathouse / tool storage. I did the work one handed, with the recovering wrist tucked in my jacket pocket.

Luckily, my supply of hardwoods, and equipment, were all up off the floor. I had a few pieces off offcut Luann, plywood, and the like stored on the floor to use as box bottoms or in later projects, but if the edges that got wet were damaged, they can be trimmed. My leather, exotics, etc were all protected. I WILL make a rack so any future flood, if any, flows thru with inconvenience only. All wood will be six or eight inches up.

We will look at a solution to improve the flow around the shop. Dyke, deeper french drain, or a drainage ditch of some sort. The shop's location was poorly chosen, at the bottom of the slope of a sixty acre hayfield, funneling all the rain AT the shop.

[BrokenolMarine]

We could remove ALL the woodworking equipment and tools, supplies, shelves, hardware. Strip the shop bare again. Then pour another four inch slab on top of the existing slab, raising the floor four inches... Then bring the equipment back in. The bandsaw would be a close call to clear the overhead though...

Almost rather build a new dedicated shop at the edge of the pasture in a year or so.

[BrokenolMarine]

Still doing my PT at home for ROM and flexibilty. Seeing a big reduction in the overall pain in the hand/wrist. The fingers have pain in the joints, and there is a distinct mechanical stop in vertical movement at this time where the plate was installed, but we are still early. There are defined pain centers on both sides of the wrist where the breaks occured, but ... We are still early.

I keep telling myself that, and push just a Little at the edges.
No pain... Must be good meds.
Actually, I cut those out except at bedtime.
The Corps has a Tshirt.
Pain... Is just weakness leaving the body.
Twenty Six surgeries.
I say, pain is progress.
I'll keep you posted.
I have knives to finish.